PA6 Settings for Voxelab Aquila
Recommended slicer settings for printing PA6 on the Voxelab Aquila (220 x 220 x 250 mm build volume, 180 mm/s max speed, Bowden extruder).
切片配置
将这些参数复制到你的切片软件（Cura、OrcaSlicer、PrusaSlicer、Bambu Studio）| 参数 | 数值 | 范围 |
|---|---|---|
| 喷嘴温度 | 255°C | 240-270°C |
| 热床温度 | 90°C | 80-100°C |
| 首层喷嘴 | 260°C | +5°C above normal |
| 首层热床 | 95°C | +5°C above normal |
| 打印速度 | 40 mm/s | 30-50 mm/s |
| 首层速度 | 15 mm/s | 25-50% of normal |
| 外壁速度 | 30 mm/s | 70-80% of normal |
| 空走速度 | 75 mm/s | 120-150% of print speed |
| 层高 | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| 壁数 | 2-3 | Perimeters/shells |
| 顶层/底层 | 3-4 | Solid layers |
| 散热风扇 | 100% | From layer 2+ |
| 回抽距离 | 4-6 mm | Bowden |
| 回抽速度 | 40 mm/s | Bowden |
开始打印前
打印质量预设
Three presets for common use cases with PA6 on the Voxelab Aquila.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
热床附着
PA6 尼龙需要 Garolite (G10) 片或 PEI 配 Magigoo PA 粘合剂,80-100°C。裙边至关重要。PA6 翘曲猛烈,必须从干燥盒打印。带胶棒的蓝色美纹纸是替代方案。
温度调校指南
Nozzle: 255°C
Range: 240-270°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 90°C
Range: 80-100°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
在 Voxelab Aquila 上打印 PA6 的问题排查
PA6 使用技巧
PA6 比 PA12 尼龙更难打印 -- 如果是尼龙新手,从 PA12 开始
干燥至关重要:80°C 16-20 小时,然后从干燥盒打印
Garolite (G10) 片为 PA6 提供最佳热床粘合
打印后,湿气调理(煮沸)PA6 零件可使抗冲击性增加三倍
支撑设置
For prints requiring supports with PA6, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Voxelab Aquila Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 180 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 100°C |
| Extruder | Bowden |
PA6 Properties
| Nozzle Range | 240-270°C |
| Bed Range | 80-100°C |
| Speed Range | 30-50 mm/s |
| Difficulty | advanced |
| Drying | 85°C / 12h |
| Enclosure | Recommended |
PA6 速览
优势
- Strongest common nylon variant
- Exceptional wear and fatigue resistance
- Good chemical resistance
- Excellent for gears, bearings, hinges
劣势
- Extremely hygroscopic — must dry extensively
- Warps aggressively without enclosure
- Difficult bed adhesion
- Shrinks significantly during cooling
想要个性化的 AI 参数？
描述你的具体配置和要打印的内容。3DSearch 的 AI 专家会在几秒内为你的 Voxelab Aquila 搭配 PA6 生成定制切片参数。
试用 3DSearch →来源： Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. 参数根据耗材规格和打印机硬件上限计算得出。