High Speed PLA Settings for Voxelab Aquila
Recommended slicer settings for printing High Speed PLA on the Voxelab Aquila (220 x 220 x 250 mm build volume, 180 mm/s max speed, Bowden extruder).
切片配置
将这些参数复制到你的切片软件（Cura、OrcaSlicer、PrusaSlicer、Bambu Studio）| 参数 | 数值 | 范围 |
|---|---|---|
| 喷嘴温度 | 210°C | 190-230°C |
| 热床温度 | 53°C | 45-60°C |
| 首层喷嘴 | 215°C | +5°C above normal |
| 首层热床 | 58°C | +5°C above normal |
| 打印速度 | 225 mm/s | 150-300 mm/s |
| 首层速度 | 75 mm/s | 25-50% of normal |
| 外壁速度 | 169 mm/s | 70-80% of normal |
| 空走速度 | 180 mm/s | 120-150% of print speed |
| 层高 | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| 壁数 | 2-3 | Perimeters/shells |
| 顶层/底层 | 3-4 | Solid layers |
| 散热风扇 | 100% | From layer 2+ |
| 回抽距离 | 4-6 mm | Bowden |
| 回抽速度 | 40 mm/s | Bowden |
开始打印前
打印质量预设
Three presets for common use cases with High Speed PLA on the Voxelab Aquila.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 300 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 225 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 150 mm/s | 20-30% | Miniatures, display pieces, fine detail |
热床附着
高速 PLA 像普通 PLA 一样粘合,但更快的打印速度意味着第一层粘合甚至更关键。使用干净的 PEI 片,将第一层放慢到正常速度的 25-50%,如果看到起翘可将热床温度提高 5°C。
温度调校指南
Nozzle: 210°C
Range: 190-230°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 53°C
Range: 45-60°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
在 Voxelab Aquila 上打印 High Speed PLA 的问题排查
High Speed PLA 使用技巧
启用输入整形(Klipper)或压力预测以减少高速伪像
高速 PLA 是为更高流量率配制的;使用高流量热端以获得最佳效果
从中等速度开始逐步增加;不是每台打印机都能处理最大额定速度
无论其他部分运行多快,第一层应始终慢(目标速度的 25-50%)
支撑设置
For prints requiring supports with High Speed PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Voxelab Aquila Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 180 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 100°C |
| Extruder | Bowden |
High Speed PLA Properties
| Nozzle Range | 190-230°C |
| Bed Range | 45-60°C |
| Speed Range | 150-300 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
High Speed PLA 速览
优势
- Prints 3-5x faster than standard PLA
- Maintains good quality at high speeds
- Lower viscosity for better flow
- Great for rapid prototyping
劣势
- Requires printer capable of high speeds
- May need higher flow rate calibration
- Slightly reduced detail at extreme speeds
想要个性化的 AI 参数？
描述你的具体配置和要打印的内容。3DSearch 的 AI 专家会在几秒内为你的 Voxelab Aquila 搭配 High Speed PLA 生成定制切片参数。
试用 3DSearch →来源： Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. 参数根据耗材规格和打印机硬件上限计算得出。