PA6 Settings for Voxelab Aquila
Recommended slicer settings for printing PA6 on the Voxelab Aquila (220 x 220 x 250 mm build volume, 180 mm/s max speed, Bowden extruder).
Конфигурация слайсера
Скопируй эти значения в свой слайсер (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Параметр | Значение | Диапазон |
|---|---|---|
| Температура сопла | 255°C | 240-270°C |
| Температура стола | 90°C | 80-100°C |
| Сопло первого слоя | 260°C | +5°C above normal |
| Стол первого слоя | 95°C | +5°C above normal |
| Скорость печати | 40 mm/s | 30-50 mm/s |
| Скорость первого слоя | 15 mm/s | 25-50% of normal |
| Скорость стен | 30 mm/s | 70-80% of normal |
| Скорость холостого хода | 75 mm/s | 120-150% of print speed |
| Высота слоя | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Количество стен | 2-3 | Perimeters/shells |
| Верхние/нижние слои | 3-4 | Solid layers |
| Вентилятор охлаждения | 100% | From layer 2+ |
| Расстояние втягивания | 4-6 mm | Bowden |
| Скорость втягивания | 40 mm/s | Bowden |
Перед печатью
Профили качества печати
Three presets for common use cases with PA6 on the Voxelab Aquila.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Адгезия стола
PA6 (Polyamide 6) прилипает как PA12, но с лучшим прилипанием. Используй текстурированный PEI или Garolite с клеевым стиком. Юбка рекомендуется.
Руководство по регулировке температуры
Nozzle: 255°C
Range: 240-270°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 90°C
Range: 80-100°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Устранение неполадок PA6 на Voxelab Aquila
Советы профессионалов для PA6
PA6 требует 255-270°C - выше, чем PA12
Текстурированная или обработанная кровать почти необходима
Напечатай юбку для лучшего прилипания
PA6 гигроскопичен - просушь как минимум 4 часа перед печатью
PA6 более прочен и гибок, чем PA12
Параметры поддержки
For prints requiring supports with PA6, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Voxelab Aquila Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 180 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 100°C |
| Extruder | Bowden |
PA6 Properties
| Nozzle Range | 240-270°C |
| Bed Range | 80-100°C |
| Speed Range | 30-50 mm/s |
| Difficulty | advanced |
| Drying | 85°C / 12h |
| Enclosure | Recommended |
PA6 с первого взгляда
Сильные стороны
- Strongest common nylon variant
- Exceptional wear and fatigue resistance
- Good chemical resistance
- Excellent for gears, bearings, hinges
Слабые стороны
- Extremely hygroscopic — must dry extensively
- Warps aggressively without enclosure
- Difficult bed adhesion
- Shrinks significantly during cooling
Хочешь персонализированные параметры ИИ?
Опиши свою точную конфигурацию и то, что ты печатаешь. Эксперт ИИ 3DSearch генерирует пользовательские параметры слайсера для твоего Voxelab Aquila с PA6 за секунды.
Попробуй 3DSearch →Источники: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Значения рассчитаны на основе спецификаций филамента и ограничений аппаратного обеспечения принтера.