BVOH Settings for Monoprice MP Voxel
Recommended slicer settings for printing BVOH on the Monoprice MP Voxel (150 x 150 x 150 mm build volume, 100 mm/s max speed, direct drive extruder).
切片配置
将这些参数复制到你的切片软件（Cura、OrcaSlicer、PrusaSlicer、Bambu Studio）| 参数 | 数值 | 范围 |
|---|---|---|
| 喷嘴温度 | 205°C | 190-220°C |
| 热床温度 | 55°C | 50-60°C |
| 首层喷嘴 | 210°C | +5°C above normal |
| 首层热床 | 60°C | +5°C above normal |
| 打印速度 | 30 mm/s | 20-40 mm/s |
| 首层速度 | 15 mm/s | 25-50% of normal |
| 外壁速度 | 23 mm/s | 70-80% of normal |
| 空走速度 | 60 mm/s | 120-150% of print speed |
| 层高 | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| 壁数 | 2-3 | Perimeters/shells |
| 顶层/底层 | 3-4 | Solid layers |
| 散热风扇 | 100% | From layer 2+ |
| 回抽距离 | 0.8-1.2 mm | Direct drive |
| 回抽速度 | 40 mm/s | Direct drive |
开始打印前
打印质量预设
Three presets for common use cases with BVOH on the Monoprice MP Voxel.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 40 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 30 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 20 mm/s | 20-30% | Miniatures, display pieces, fine detail |
热床附着
BVOH 是类似 PVA 的水溶性支撑材料。它粘合到你的主要材料使用的任何热床表面。使用 50-70°C 的热床温度。BVOH 在温水中溶解比 PVA 更快。
温度调校指南
Nozzle: 205°C
Range: 190-220°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 55°C
Range: 50-60°C. Printer max: 60°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
在 Monoprice MP Voxel 上打印 BVOH 的问题排查
BVOH 使用技巧
始终使用干燥剂密闭储存 BVOH -- 它实际上在空气水分中溶解
从干燥盒打印并在打开后立即使用线轴
温水(40-50°C)配温和搅动比 PVA 更快溶解 BVOH;定期更换水
与 PLA 或 PETG 作为主要材料使用 BVOH;温度相容性很重要
支撑设置
For prints requiring supports with BVOH, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Monoprice MP Voxel Specs
| Build Volume | 150 x 150 x 150 mm |
| Max Speed | 100 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 60°C |
| Extruder | Direct Drive |
BVOH Properties
| Nozzle Range | 190-220°C |
| Bed Range | 50-60°C |
| Speed Range | 20-40 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
BVOH 速览
优势
- Water-soluble support material
- Dissolves faster than PVA (2-4 hours)
- Works with wider range of build materials
- Leaves very clean supported surfaces
劣势
- Extremely moisture sensitive — use immediately after opening
- More expensive than PVA
- Must store in sealed dry container
- Limited shelf life once opened
想要个性化的 AI 参数？
描述你的具体配置和要打印的内容。3DSearch 的 AI 专家会在几秒内为你的 Monoprice MP Voxel 搭配 BVOH 生成定制切片参数。
试用 3DSearch →来源： Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. 参数根据耗材规格和打印机硬件上限计算得出。