Breakaway Support Settings for Voxelab Aquila X2
Recommended slicer settings for printing Breakaway Support on the Voxelab Aquila X2 (220 x 220 x 250 mm build volume, 180 mm/s max speed, Bowden extruder).
הגדרות Slicer
העתק את הערכים האלה ל-Slicer שלך (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| הגדרה | ערך | טווח |
|---|---|---|
| טמפרטורת חרירון | 225°C | 210-240°C |
| טמפרטורת משטח | 60°C | 50-70°C |
| חרירון בשכבה ראשונה | 230°C | +5°C above normal |
| משטח בשכבה ראשונה | 65°C | +5°C above normal |
| מהירות הדפסה | 40 mm/s | 30-50 mm/s |
| מהירות שכבה ראשונה | 15 mm/s | 25-50% of normal |
| מהירות דפנות | 30 mm/s | 70-80% of normal |
| מהירות תנועה | 75 mm/s | 120-150% of print speed |
| גובה שכבה | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| מספר דפנות | 2-3 | Perimeters/shells |
| שכבות עליונות/תחתונות | 3-4 | Solid layers |
| מאוורר קירור | 100% | From layer 2+ |
| מרחק נסיגה | 4-6 mm | Bowden |
| מהירות נסיגה | 40 mm/s | Bowden |
לפני שמדפיסים
פרופילי איכות הדפסה
Three presets for common use cases with Breakaway Support on the Voxelab Aquila X2.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
היצמדות למשטח
Breakaway support material adheres to whatever build surface your main material uses. Bed temperature should match the main filament. After printing, snap off supports mechanically — no solvents needed.
מדריך כיוון טמפרטורה
Nozzle: 225°C
Range: 210-240°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 60°C
Range: 50-70°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
פתרון תקלות Breakaway Support על Voxelab Aquila X2
טיפים מקצועיים ל-Breakaway Support
Breakaway supports snap off mechanically -- no solvents or water required
Adjust Z-gap and interface density to balance support strength vs. ease of removal
Breakaway is faster to remove than soluble supports like PVA/BVOH for simple overhangs
Use soluble supports instead for complex internal geometries where mechanical access is difficult
הגדרות תמיכות
For prints requiring supports with Breakaway Support, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Voxelab Aquila X2 Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 180 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 100°C |
| Extruder | Bowden |
Breakaway Support Properties
| Nozzle Range | 210-240°C |
| Bed Range | 50-70°C |
| Speed Range | 30-50 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
Breakaway Support במבט מהיר
יתרונות
- Snaps off cleanly without solvents
- Fast removal — no dissolving wait time
- Works with most build materials
- No special post-processing needed
חסרונות
- Leaves rougher surface than dissolved supports
- Requires accessible support geometry
- Not suitable for internal cavities
- May need pliers for tight areas
רוצה הגדרות AI מותאמות אישית?
תאר את ההגדרה המדויקת שלך ואת מה שאתה מדפיס. מומחה ה-AI של 3DSearch מייצר הגדרות סלייסר מותאמות עבור ה-Voxelab Aquila X2 שלך עם Breakaway Support תוך שניות.
נסה את 3DSearch →מקורות: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. הערכים חושבו ממפרטי הפילמנט וממגבלות החומרה של המדפסת.