Kevlar-fill Nylon Settings for Voxelab Aquila X2
Recommended slicer settings for printing Kevlar-fill Nylon on the Voxelab Aquila X2 (220 x 220 x 250 mm build volume, 180 mm/s max speed, Bowden extruder).
Slicer Configuration
Copy these values into your slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Setting | Value | Range |
|---|---|---|
| Nozzle Temperature | 260°C | 245-275°C |
| Bed Temperature | 93°C | 85-100°C |
| First Layer Nozzle | 260°C | At printer max |
| First Layer Bed | 98°C | +5°C above normal |
| Print Speed | 35 mm/s | 25-45 mm/s |
| First Layer Speed | 15 mm/s | 25-50% of normal |
| Wall Speed | 26 mm/s | 70-80% of normal |
| Travel Speed | 68 mm/s | 120-150% of print speed |
| Layer Height | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Wall Count | 2-3 | Perimeters/shells |
| Top/Bottom Layers | 3-4 | Solid layers |
| Cooling Fan | 100% | From layer 2+ |
| Retraction Distance | 4-6 mm | Bowden |
| Retraction Speed | 40 mm/s | Bowden |
Before You Print
Print Quality Profiles
Three presets for common use cases with Kevlar-fill Nylon on the Voxelab Aquila X2.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 45 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 35 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 25 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Bed Adhesion
Kevlar-fill nylon uses the same adhesion methods as standard nylon: Garolite (G10) sheet or PEI with Magigoo PA adhesive at 70-90°C. A brim is essential. Print from a dry box.
Temperature Tuning Guide
Nozzle: 260°C
Range: 245-275°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 93°C
Range: 85-100°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Troubleshooting Kevlar-fill Nylon on Voxelab Aquila X2
Pro Tips for Kevlar-fill Nylon
Hardened steel nozzle (0.5mm+) is mandatory for kevlar fibers
Same drying protocol as nylon: 80°C for 12+ hours, print from dry box
Kevlar-fill nylon provides excellent impact resistance combined with nylon's wear resistance
Enclosure and Garolite bed are essential for reliable printing
Support Settings
For prints requiring supports with Kevlar-fill Nylon, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Voxelab Aquila X2 Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 180 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 100°C |
| Extruder | Bowden |
Kevlar-fill Nylon Properties
| Nozzle Range | 245-275°C |
| Bed Range | 85-100°C |
| Speed Range | 25-45 mm/s |
| Difficulty | advanced |
| Drying | 85°C / 12h |
| Enclosure | Recommended |
Kevlar-fill Nylon at a Glance
Strengths
- Kevlar fibers add toughness without brittleness
- Better impact resistance than carbon fiber nylon
- Good abrasion resistance
- Lighter than carbon fiber composites
Weaknesses
- Hardened nozzle required
- Very hygroscopic
- Expensive and limited availability
- Lower stiffness than carbon fiber variants
Want personalized AI settings?
Describe your exact setup and what you are printing. 3DSearch's AI expert generates custom slicer settings for your Voxelab Aquila X2 with Kevlar-fill Nylon in seconds.
Try 3DSearch →Sources: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Values calculated from filament specifications and printer hardware limits.