PA12-CF Settings for Anycubic Kobra 2 Plus
Recommended slicer settings for printing PA12-CF on the Anycubic Kobra 2 Plus (320 x 320 x 400 mm build volume, 300 mm/s max speed, direct drive extruder).
切片配置
将这些参数复制到你的切片软件（Cura、OrcaSlicer、PrusaSlicer、Bambu Studio）| 参数 | 数值 | 范围 |
|---|---|---|
| 喷嘴温度 | 260°C | 260-280°C |
| 热床温度 | 90°C | 80-100°C |
| 首层喷嘴 | 260°C | At printer max |
| 首层热床 | 90°C | At printer max |
| 打印速度 | 35 mm/s | 25-45 mm/s |
| 首层速度 | 15 mm/s | 25-50% of normal |
| 外壁速度 | 26 mm/s | 70-80% of normal |
| 空走速度 | 68 mm/s | 120-150% of print speed |
| 层高 | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| 壁数 | 2-3 | Perimeters/shells |
| 顶层/底层 | 3-4 | Solid layers |
| 散热风扇 | 0-10% | From layer 2+ |
| 回抽距离 | 0.8-1.2 mm | Direct drive |
| 回抽速度 | 40 mm/s | Direct drive |
开始打印前
打印质量预设
Three presets for common use cases with PA12-CF on the Anycubic Kobra 2 Plus.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 45 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 35 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 25 mm/s | 20-30% | Miniatures, display pieces, fine detail |
热床附着
PA12-CF 需要高温下的强热床粘合。在 80-100°C 使用 PEI 片或 Garolite (G10) 片。大多数打印件必须使用裙边。胶棒或 Magigoo PA 粘合剂提供最佳效果。从干燥盒打印以避免受潮相关的粘合故障。
温度调校指南
Nozzle: 260°C
Range: 260-280°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 90°C
Range: 80-100°C. Printer max: 90°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
在 Anycubic Kobra 2 Plus 上打印 PA12-CF 的问题排查
PA12-CF 使用技巧
PA12-CF 所需的 260-280°C 范围内全金属热端是强制的
始终从干燥盒打印 -- PA12-CF 吸收会破坏打印质量的水分
使用硬化钢喷嘴(0.5mm+)以处理磨料碳纤维
彻底密封你的外罩;PA12-CF 在气流中翘曲很猛烈
PA12-CF 比 PA6-CF 更容易打印且吸水性更低 -- 尼龙-CF 打印的好入门点
支撑设置
For prints requiring supports with PA12-CF, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 2 Plus Specs
| Build Volume | 320 x 320 x 400 mm |
| Max Speed | 300 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 90°C |
| Extruder | Direct Drive |
PA12-CF Properties
| Nozzle Range | 260-280°C |
| Bed Range | 80-100°C |
| Speed Range | 25-45 mm/s |
| Difficulty | advanced |
| Drying | 80°C / 12h |
| Enclosure | Recommended |
PA12-CF 速览
优势
- Exceptional stiffness-to-weight ratio
- Excellent heat resistance (HDT ~140C under load)
- Lower moisture absorption than PA6-CF
- Professional matte finish with dimensional stability
- Ideal for high-performance jigs, drone frames, and tooling
劣势
- Requires hardened steel nozzle (mandatory)
- Requires all-metal hotend for 260-280C range
- Must be dried extensively and printed from dry box
- Enclosure required to prevent warping and delamination
- Expensive (~$50-80/kg) and limited color options
想要个性化的 AI 参数？
描述你的具体配置和要打印的内容。3DSearch 的 AI 专家会在几秒内为你的 Anycubic Kobra 2 Plus 搭配 PA12-CF 生成定制切片参数。
试用 3DSearch →来源： Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. 参数根据耗材规格和打印机硬件上限计算得出。