PA12-CF Settings for Anycubic Kobra 2 Plus
Recommended slicer settings for printing PA12-CF on the Anycubic Kobra 2 Plus (320 x 320 x 400 mm build volume, 300 mm/s max speed, direct drive extruder).
Slicer Configuration
Copy these values into your slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Setting | Value | Range |
|---|---|---|
| Nozzle Temperature | 260°C | 260-280°C |
| Bed Temperature | 90°C | 80-100°C |
| First Layer Nozzle | 260°C | At printer max |
| First Layer Bed | 90°C | At printer max |
| Print Speed | 35 mm/s | 25-45 mm/s |
| First Layer Speed | 15 mm/s | 25-50% of normal |
| Wall Speed | 26 mm/s | 70-80% of normal |
| Travel Speed | 68 mm/s | 120-150% of print speed |
| Layer Height | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Wall Count | 2-3 | Perimeters/shells |
| Top/Bottom Layers | 3-4 | Solid layers |
| Cooling Fan | 0-10% | From layer 2+ |
| Retraction Distance | 0.8-1.2 mm | Direct drive |
| Retraction Speed | 40 mm/s | Direct drive |
Before You Print
Print Quality Profiles
Three presets for common use cases with PA12-CF on the Anycubic Kobra 2 Plus.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 45 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 35 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 25 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Bed Adhesion
PA12-CF requires strong bed adhesion at high temperatures. Use a PEI sheet or Garolite (G10) sheet at 80-100°C. A brim is essential for most prints. Glue stick or Magigoo PA adhesive provides the best results. Print from a dry box to avoid moisture-related adhesion failures.
Temperature Tuning Guide
Nozzle: 260°C
Range: 260-280°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 90°C
Range: 80-100°C. Printer max: 90°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Troubleshooting PA12-CF on Anycubic Kobra 2 Plus
Pro Tips for PA12-CF
An all-metal hotend is mandatory for the 260-280°C range required by PA12-CF
Always print from a dry box -- PA12-CF absorbs moisture that ruins print quality
Use a hardened steel nozzle (0.5mm+) to handle the abrasive carbon fibers
Seal your enclosure thoroughly; PA12-CF warps aggressively in drafts
PA12-CF is easier to print than PA6-CF and absorbs less moisture -- a good entry point to nylon-CF printing
Support Settings
For prints requiring supports with PA12-CF, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 2 Plus Specs
| Build Volume | 320 x 320 x 400 mm |
| Max Speed | 300 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 90°C |
| Extruder | Direct Drive |
PA12-CF Properties
| Nozzle Range | 260-280°C |
| Bed Range | 80-100°C |
| Speed Range | 25-45 mm/s |
| Difficulty | advanced |
| Drying | 80°C / 12h |
| Enclosure | Recommended |
PA12-CF at a Glance
Strengths
- Exceptional stiffness-to-weight ratio
- Excellent heat resistance (HDT ~140C under load)
- Lower moisture absorption than PA6-CF
- Professional matte finish with dimensional stability
- Ideal for high-performance jigs, drone frames, and tooling
Weaknesses
- Requires hardened steel nozzle (mandatory)
- Requires all-metal hotend for 260-280C range
- Must be dried extensively and printed from dry box
- Enclosure required to prevent warping and delamination
- Expensive (~$50-80/kg) and limited color options
Want personalized AI settings?
Describe your exact setup and what you are printing. 3DSearch's AI expert generates custom slicer settings for your Anycubic Kobra 2 Plus with PA12-CF in seconds.
Try 3DSearch →Sources: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Values calculated from filament specifications and printer hardware limits.