PA6 Settings for Creality CR-10 Smart Pro
Recommended slicer settings for printing PA6 on the Creality CR-10 Smart Pro (300 x 300 x 400 mm build volume, 100 mm/s max speed, direct drive extruder).
Slicer-Konfiguration
Kopiere diese Werte in deinen Slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Einstellung | Wert | Bereich |
|---|---|---|
| Düsentemperatur | 255°C | 240-270°C |
| Heizbetttemperatur | 90°C | 80-100°C |
| Erste Schicht Düse | 260°C | +5°C above normal |
| Erste Schicht Heizbett | 95°C | +5°C above normal |
| Druckgeschwindigkeit | 40 mm/s | 30-50 mm/s |
| Erste Schicht Geschwindigkeit | 15 mm/s | 25-50% of normal |
| Wandgeschwindigkeit | 30 mm/s | 70-80% of normal |
| Verfahrgeschwindigkeit | 75 mm/s | 120-150% of print speed |
| Schichthöhe | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Wandanzahl | 2-3 | Perimeters/shells |
| Oben/Unten Schichten | 3-4 | Solid layers |
| Kühlventilator | 100% | From layer 2+ |
| Rückzugsdistanz | 0.8-1.2 mm | Direct drive |
| Rückzugsgeschwindigkeit | 40 mm/s | Direct drive |
Vor dem Drucken
Druckqualität Profile
Three presets for common use cases with PA6 on the Creality CR-10 Smart Pro.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Haftung des Heizbetts
PA6 (Polyamid 6) haftet ähnlich wie PA12 aber mit besserer Haftung. Verwende strukturiertes PEI oder Garolite mit Klebestift. Ein Brim wird empfohlen.
Temperatur-Abstimmungsanleitung
Nozzle: 255°C
Range: 240-270°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 90°C
Range: 80-100°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Fehlerbehebung PA6 auf Creality CR-10 Smart Pro
Pro-Tipps für PA6
PA6 benötigt 255-270°C - höher als PA12
Ein strukturiertes oder behandeltes Bett ist fast obligatorisch
Drucke einen Brim für bessere Haftung
PA6 ist hygroskopisch - trockne mindestens 4 Stunden vor Druck
PA6 ist langlebiger und flexibler als PA12
Support-Einstellungen
For prints requiring supports with PA6, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Creality CR-10 Smart Pro Specs
| Build Volume | 300 x 300 x 400 mm |
| Max Speed | 100 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 100°C |
| Extruder | Direct Drive |
PA6 Properties
| Nozzle Range | 240-270°C |
| Bed Range | 80-100°C |
| Speed Range | 30-50 mm/s |
| Difficulty | advanced |
| Drying | 85°C / 12h |
| Enclosure | Recommended |
PA6 auf einen Blick
Stärken
- Strongest common nylon variant
- Exceptional wear and fatigue resistance
- Good chemical resistance
- Excellent for gears, bearings, hinges
Schwächen
- Extremely hygroscopic — must dry extensively
- Warps aggressively without enclosure
- Difficult bed adhesion
- Shrinks significantly during cooling
Möchtest du personalisierte KI-Einstellungen?
Beschreibe dein genaues Setup und was du druckst. 3DSearch's KI-Experte erzeugt in Sekunden individuelle Slicer-Einstellungen für deinen Creality CR-10 Smart Pro mit PA6.
3DSearch ausprobieren →Quellen: Based on Creality support documentation, community testing data, manufacturer recommended ranges. Werte berechnet aus Filament-Spezifikationen und Drucker-Hardware-Limits.