PETG-CF Settings for Anycubic Kobra 3
Recommended slicer settings for printing PETG-CF on the Anycubic Kobra 3 (250 x 250 x 260 mm build volume, 600 mm/s max speed, direct drive extruder).
Slicer-configuratie
Kopieer deze waarden naar je slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Instelling | Waarde | Bereik |
|---|---|---|
| Mondstuktemperatuur | 245°C | 230-260°C |
| Bedtemperatuur | 75°C | 70-80°C |
| Eerste laag mondstuk | 250°C | +5°C above normal |
| Eerste laag bed | 80°C | +5°C above normal |
| Afdruksnelheid | 40 mm/s | 30-50 mm/s |
| Eerste laag snelheid | 15 mm/s | 25-50% of normal |
| Muursnelheid | 30 mm/s | 70-80% of normal |
| Reissnelheid | 75 mm/s | 120-150% of print speed |
| Laagdikte | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Muurantal | 2-3 | Perimeters/shells |
| Boven-/onderlagen | 3-4 | Solid layers |
| Koelventilator | 30-50% | From layer 2+ |
| Intrekngsafstand | 0.8-1.2 mm | Direct drive |
| Intreksnelheid | 40 mm/s | Direct drive |
Voordat je afdrukt
Afdrukprofielen kwaliteit
Three presets for common use cases with PETG-CF on the Anycubic Kobra 3.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Adhesie bed
PETG Koolstofvezel hecht vergelijkbaar met normale PETG, soms beter door vezzelruwheid. Gebruik PEI-platen of gestructureerde oppervlakken.
Temperatuurafstemmingsgids
Nozzle: 245°C
Range: 230-260°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 75°C
Range: 70-80°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Problemen oplossen PETG-CF op Anycubic Kobra 3
Pro tips voor PETG-CF
Geharde staal-nozzle is nodig
Druk op vergelijkbare temperaturen als normale PETG plus 5°C
Verhoog doorvoersnelheid met 10% door deeltjesdichtheid
PETG Koolstofvezel is stijver en lichter dan normale PETG
Droog voor afdruk - PETG is hygroskopisch
Ondersteuningsinstellingen
For prints requiring supports with PETG-CF, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 3 Specs
| Build Volume | 250 x 250 x 260 mm |
| Max Speed | 600 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
PETG-CF Properties
| Nozzle Range | 230-260°C |
| Bed Range | 70-80°C |
| Speed Range | 30-50 mm/s |
| Difficulty | intermediate |
| Drying | 65°C / 8h |
| Enclosure | Not needed |
PETG-CF in één oogopslag
Sterke punten
- Significantly stiffer than standard PETG
- Professional matte surface finish
- Reduced warping compared to plain PETG
- Good chemical and moisture resistance
- Excellent for functional brackets, jigs, and fixtures
Zwakke punten
- Requires hardened steel nozzle (carbon fibers destroy brass)
- More brittle than standard PETG (reduced flexibility)
- Must use 0.5mm+ nozzle to prevent clogging
- Slower print speeds required than standard PETG
- Higher cost than plain PETG ($30-45/kg)
Wil je gepersonaliseerde AI-instellingen?
Beschrijf je exacte setup en wat je afdrukt. 3DSearch's AI-expert genereert in seconden aangepaste slicer-instellingen voor je Anycubic Kobra 3 met PETG-CF.
Probeer 3DSearch →Bronnen: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Waarden berekend op basis van filamentspecificaties en printerhard warelimiet.