TPE Settings for Anycubic Kobra 2
Recommended slicer settings for printing TPE on the Anycubic Kobra 2 (220 x 220 x 250 mm build volume, 300 mm/s max speed, direct drive extruder).
切片配置
将这些参数复制到你的切片软件（Cura、OrcaSlicer、PrusaSlicer、Bambu Studio）| 参数 | 数值 | 范围 |
|---|---|---|
| 喷嘴温度 | 215°C | 200-230°C |
| 热床温度 | 40°C | 30-50°C |
| 首层喷嘴 | 220°C | +5°C above normal |
| 首层热床 | 45°C | +5°C above normal |
| 打印速度 | 18 mm/s | 10-25 mm/s |
| 首层速度 | 15 mm/s | 25-50% of normal |
| 外壁速度 | 14 mm/s | 70-80% of normal |
| 空走速度 | 38 mm/s | 120-150% of print speed |
| 层高 | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| 壁数 | 3-4 | Perimeters/shells |
| 顶层/底层 | 5-6 | Solid layers |
| 散热风扇 | 100% | From layer 2+ |
| 回抽距离 | 0.8-1.2 mm | Direct drive |
| 回抽速度 | 40 mm/s | Direct drive |
开始打印前
打印质量预设
Three presets for common use cases with TPE on the Anycubic Kobra 2.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 25 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 18 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 10 mm/s | 20-30% | Miniatures, display pieces, fine detail |
热床附着
TPE 粘合良好到 PEI 片和蓝色美纹纸。像 TPU 一样,粘合通常对柔性耗材不是问题。对第一层使用缓慢速度以获得最佳效果。
温度调校指南
Nozzle: 215°C
Range: 200-230°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 40°C
Range: 30-50°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
在 Anycubic Kobra 2 上打印 TPE 的问题排查
TPE 使用技巧
TPE 比标准 TPU 更软 -- 直接驱动挤出机本质上是强制的
在 15-30 mm/s 打印;速度是 TPE 打印故障的首要原因
最小化回抽至直接驱动 0.3-0.8mm;不推荐 Bowden
TPE 因其皮肤安全的灵活性而在垫片、软握把和可穿戴物品中表现出色
支撑设置
For prints requiring supports with TPE, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 2 Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 300 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
TPE Properties
| Nozzle Range | 200-230°C |
| Bed Range | 30-50°C |
| Speed Range | 10-25 mm/s |
| Difficulty | advanced |
| Drying | 50°C / 5h |
| Enclosure | Not needed |
TPE 速览
优势
- Softer than TPU — very rubber-like
- Excellent elasticity and memory
- Good for very flexible parts
- Chemical resistant
劣势
- Extremely difficult to print
- Direct drive required — impossible on Bowden
- Very slow speeds only
- Poor detail resolution due to softness
想要个性化的 AI 参数？
描述你的具体配置和要打印的内容。3DSearch 的 AI 专家会在几秒内为你的 Anycubic Kobra 2 搭配 TPE 生成定制切片参数。
试用 3DSearch →来源： Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. 参数根据耗材规格和打印机硬件上限计算得出。