PA6 Settings for Anycubic Kobra 3 Combo
Recommended slicer settings for printing PA6 on the Anycubic Kobra 3 Combo (250 x 250 x 260 mm build volume, 600 mm/s max speed, direct drive extruder).
Slicer-configuratie
Kopieer deze waarden naar je slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Instelling | Waarde | Bereik |
|---|---|---|
| Mondstuktemperatuur | 255°C | 240-270°C |
| Bedtemperatuur | 90°C | 80-100°C |
| Eerste laag mondstuk | 260°C | +5°C above normal |
| Eerste laag bed | 95°C | +5°C above normal |
| Afdruksnelheid | 40 mm/s | 30-50 mm/s |
| Eerste laag snelheid | 15 mm/s | 25-50% of normal |
| Muursnelheid | 30 mm/s | 70-80% of normal |
| Reissnelheid | 75 mm/s | 120-150% of print speed |
| Laagdikte | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Muurantal | 2-3 | Perimeters/shells |
| Boven-/onderlagen | 3-4 | Solid layers |
| Koelventilator | 100% | From layer 2+ |
| Intrekngsafstand | 0.8-1.2 mm | Direct drive |
| Intreksnelheid | 40 mm/s | Direct drive |
Voordat je afdrukt
Afdrukprofielen kwaliteit
Three presets for common use cases with PA6 on the Anycubic Kobra 3 Combo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Adhesie bed
PA6 (Poliamide 6) hecht vergelijkbaar met PA12 maar met betere hechting. Gebruik gestructureerde PEI of Garolite met lijmstift. Een rand wordt aanbevolen.
Temperatuurafstemmingsgids
Nozzle: 255°C
Range: 240-270°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 90°C
Range: 80-100°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Problemen oplossen PA6 op Anycubic Kobra 3 Combo
Pro tips voor PA6
PA6 vereist 255-270°C - hoger dan PA12
Gestructureerd of behandeld bed is bijna verplicht
Druk rand voor betere hechting
PA6 is hygroskopisch - droog minstens 4 uur voor afdruk
PA6 is duurzamer en flexibeler dan PA12
Ondersteuningsinstellingen
For prints requiring supports with PA6, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 3 Combo Specs
| Build Volume | 250 x 250 x 260 mm |
| Max Speed | 600 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
PA6 Properties
| Nozzle Range | 240-270°C |
| Bed Range | 80-100°C |
| Speed Range | 30-50 mm/s |
| Difficulty | advanced |
| Drying | 85°C / 12h |
| Enclosure | Recommended |
PA6 in één oogopslag
Sterke punten
- Strongest common nylon variant
- Exceptional wear and fatigue resistance
- Good chemical resistance
- Excellent for gears, bearings, hinges
Zwakke punten
- Extremely hygroscopic — must dry extensively
- Warps aggressively without enclosure
- Difficult bed adhesion
- Shrinks significantly during cooling
Wil je gepersonaliseerde AI-instellingen?
Beschrijf je exacte setup en wat je afdrukt. 3DSearch's AI-expert genereert in seconden aangepaste slicer-instellingen voor je Anycubic Kobra 3 Combo met PA6.
Probeer 3DSearch →Bronnen: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Waarden berekend op basis van filamentspecificaties en printerhard warelimiet.