TPC Settings for Anycubic Kobra 2 Max
Recommended slicer settings for printing TPC on the Anycubic Kobra 2 Max (420 x 420 x 500 mm build volume, 300 mm/s max speed, direct drive extruder).
Slicer-configuratie
Kopieer deze waarden naar je slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Instelling | Waarde | Bereik |
|---|---|---|
| Mondstuktemperatuur | 225°C | 210-240°C |
| Bedtemperatuur | 50°C | 40-60°C |
| Eerste laag mondstuk | 230°C | +5°C above normal |
| Eerste laag bed | 55°C | +5°C above normal |
| Afdruksnelheid | 23 mm/s | 15-30 mm/s |
| Eerste laag snelheid | 15 mm/s | 25-50% of normal |
| Muursnelheid | 17 mm/s | 70-80% of normal |
| Reissnelheid | 45 mm/s | 120-150% of print speed |
| Laagdikte | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Muurantal | 3-4 | Perimeters/shells |
| Boven-/onderlagen | 5-6 | Solid layers |
| Koelventilator | 100% | From layer 2+ |
| Intrekngsafstand | 0.8-1.2 mm | Direct drive |
| Intreksnelheid | 40 mm/s | Direct drive |
Voordat je afdrukt
Afdrukprofielen kwaliteit
Three presets for common use cases with TPC on the Anycubic Kobra 2 Max.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 30 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 23 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 15 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Adhesie bed
TPC hecht aan PEI-platen en glazen bedden. Hechting is vergelijkbaar met TPU.
Temperatuurafstemmingsgids
Nozzle: 225°C
Range: 210-240°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 50°C
Range: 40-60°C. Printer max: 90°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Problemen oplossen TPC op Anycubic Kobra 2 Max
Pro tips voor TPC
TPC is thermoplastisch copolyester - flexibel als TPU maar iets stijver
Druk langzaam - 20-40 mm/s
Directe aandrijving wordt sterk aanbevolen
Minimaliseer retractie - 0.5-1mm is genoeg
Materiaal is ideaal voor flexibele onderdelen
Ondersteuningsinstellingen
For prints requiring supports with TPC, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 2 Max Specs
| Build Volume | 420 x 420 x 500 mm |
| Max Speed | 300 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 90°C |
| Extruder | Direct Drive |
TPC Properties
| Nozzle Range | 210-240°C |
| Bed Range | 40-60°C |
| Speed Range | 15-30 mm/s |
| Difficulty | intermediate |
| Drying | 50°C / 5h |
| Enclosure | Not needed |
TPC in één oogopslag
Sterke punten
- Flexible co-polyester — better chemical resistance than TPU
- Good UV resistance for outdoor flexible parts
- Better printability than TPE
- Good temperature resistance
Zwakke punten
- Less flexible than TPU at same hardness
- More expensive than TPU
- Limited brand availability
- Fewer color options
Wil je gepersonaliseerde AI-instellingen?
Beschrijf je exacte setup en wat je afdrukt. 3DSearch's AI-expert genereert in seconden aangepaste slicer-instellingen voor je Anycubic Kobra 2 Max met TPC.
Probeer 3DSearch →Bronnen: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Waarden berekend op basis van filamentspecificaties en printerhard warelimiet.