PETG Settings for Voxelab Aquila X2
Recommended slicer settings for printing PETG on the Voxelab Aquila X2 (220 x 220 x 250 mm build volume, 180 mm/s max speed, Bowden extruder).
הגדרות Slicer
העתק את הערכים האלה ל-Slicer שלך (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| הגדרה | ערך | טווח |
|---|---|---|
| טמפרטורת חרירון | 240°C | 230-250°C |
| טמפרטורת משטח | 85°C | 80-90°C |
| חרירון בשכבה ראשונה | 245°C | +5°C above normal |
| משטח בשכבה ראשונה | 90°C | +5°C above normal |
| מהירות הדפסה | 50 mm/s | 40-60 mm/s |
| מהירות שכבה ראשונה | 20 mm/s | 25-50% of normal |
| מהירות דפנות | 38 mm/s | 70-80% of normal |
| מהירות תנועה | 90 mm/s | 120-150% of print speed |
| גובה שכבה | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| מספר דפנות | 2-3 | Perimeters/shells |
| שכבות עליונות/תחתונות | 3-4 | Solid layers |
| מאוורר קירור | 30-50% | From layer 2+ |
| מרחק נסיגה | 4-6 mm | Bowden |
| מהירות נסיגה | 40 mm/s | Bowden |
לפני שמדפיסים
פרופילי איכות הדפסה
Three presets for common use cases with PETG on the Voxelab Aquila X2.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 60 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 50 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 40 mm/s | 20-30% | Miniatures, display pieces, fine detail |
היצמדות למשטח
PETG bonds extremely well to smooth PEI sheets -- sometimes too well. Use a textured PEI sheet or apply a thin layer of glue stick as a release agent on smooth PEI to prevent damage. On glass beds, always use glue stick (PETG can pull glass chips off). Let the bed cool completely before removing prints.
מדריך כיוון טמפרטורה
Nozzle: 240°C
Range: 230-250°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 85°C
Range: 80-90°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
פתרון תקלות PETG על Voxelab Aquila X2
טיפים מקצועיים ל-PETG
Dry your PETG before printing -- even a new spool left open overnight can absorb enough moisture to affect quality
Slow down the first layer to 15-20 mm/s for solid adhesion
Use a lower fan speed (30-50%) -- too much cooling weakens layer adhesion with PETG
If printing on smooth PEI, use glue stick as a release agent to prevent bed damage
PETG is an excellent all-around material once you dial in the settings
הגדרות תמיכות
For prints requiring supports with PETG, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Voxelab Aquila X2 Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 180 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 100°C |
| Extruder | Bowden |
PETG Properties
| Nozzle Range | 230-250°C |
| Bed Range | 80-90°C |
| Speed Range | 40-60 mm/s |
| Difficulty | beginner |
| Drying | 65°C / 7h |
| Enclosure | Not needed |
PETG במבט מהיר
יתרונות
- Excellent all-around material for functional parts
- Good impact resistance (much better than PLA)
- Moderate heat resistance (softens ~80C)
- FDA-approved for food contact in raw form
- Good chemical resistance
- Semi-flexible (bends before breaking)
חסרונות
- Prone to stringing
- Moderate moisture sensitivity
- Can bond too strongly to glass beds
- Lower fan speeds required (not great for overhangs)
רוצה הגדרות AI מותאמות אישית?
תאר את ההגדרה המדויקת שלך ואת מה שאתה מדפיס. מומחה ה-AI של 3DSearch מייצר הגדרות סלייסר מותאמות עבור ה-Voxelab Aquila X2 שלך עם PETG תוך שניות.
נסה את 3DSearch →מקורות: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. הערכים חושבו ממפרטי הפילמנט וממגבלות החומרה של המדפסת.