TPU Settings for Anycubic Kobra 3 Combo
Recommended slicer settings for printing TPU on the Anycubic Kobra 3 Combo (250 x 250 x 260 mm build volume, 600 mm/s max speed, direct drive extruder).
הגדרות Slicer
העתק את הערכים האלה ל-Slicer שלך (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| הגדרה | ערך | טווח |
|---|---|---|
| טמפרטורת חרירון | 225°C | 210-240°C |
| טמפרטורת משטח | 50°C | 40-60°C |
| חרירון בשכבה ראשונה | 230°C | +5°C above normal |
| משטח בשכבה ראשונה | 55°C | +5°C above normal |
| מהירות הדפסה | 35 mm/s | 20-50 mm/s |
| מהירות שכבה ראשונה | 15 mm/s | 25-50% of normal |
| מהירות דפנות | 26 mm/s | 70-80% of normal |
| מהירות תנועה | 75 mm/s | 120-150% of print speed |
| גובה שכבה | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| מספר דפנות | 3-4 | Perimeters/shells |
| שכבות עליונות/תחתונות | 5-6 | Solid layers |
| מאוורר קירור | 100% | From layer 2+ |
| מרחק נסיגה | 0.5-1.0 mm | Direct drive |
| מהירות נסיגה | 25 mm/s | Direct drive |
לפני שמדפיסים
פרופילי איכות הדפסה
Three presets for common use cases with TPU on the Anycubic Kobra 3 Combo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 35 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 20 mm/s | 20-30% | Miniatures, display pieces, fine detail |
היצמדות למשטח
TPU adheres well to most surfaces including PEI sheets, blue painter's tape, and glass with glue stick. Adhesion is rarely an issue with TPU.
מדריך כיוון טמפרטורה
Nozzle: 225°C
Range: 210-240°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 50°C
Range: 40-60°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
פתרון תקלות TPU על Anycubic Kobra 3 Combo
טיפים מקצועיים ל-TPU
Speed is the most critical setting -- printing too fast is the number one cause of TPU failures
A direct drive extruder is strongly recommended; Bowden setups struggle with flexible filaments
Minimize retraction (0.5-1mm on direct drive) -- excessive retraction causes jams
Dry your TPU before every use in humid climates; it is very hygroscopic
Consider starting with Shore 95A TPU -- it is the easiest flexible filament to print
הגדרות תמיכות
For prints requiring supports with TPU, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 3 Combo Specs
| Build Volume | 250 x 250 x 260 mm |
| Max Speed | 600 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
TPU Properties
| Nozzle Range | 210-240°C |
| Bed Range | 40-60°C |
| Speed Range | 20-50 mm/s |
| Difficulty | intermediate |
| Drying | 70°C / 7h |
| Enclosure | Not needed |
TPU במבט מהיר
יתרונות
- Flexible and rubber-like
- Excellent impact absorption
- Excellent abrasion resistance
- 300-600% elongation at break
- Great for phone cases, gaskets, wheels, dampeners
חסרונות
- Must print very slowly
- Difficult on Bowden extruders
- High moisture sensitivity
- Stringing is common
- Retraction must be minimized
רוצה הגדרות AI מותאמות אישית?
תאר את ההגדרה המדויקת שלך ואת מה שאתה מדפיס. מומחה ה-AI של 3DSearch מייצר הגדרות סלייסר מותאמות עבור ה-Anycubic Kobra 3 Combo שלך עם TPU תוך שניות.
נסה את 3DSearch →מקורות: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. הערכים חושבו ממפרטי הפילמנט וממגבלות החומרה של המדפסת.