HIPS Settings for Anycubic Kobra 3 Combo
Recommended slicer settings for printing HIPS on the Anycubic Kobra 3 Combo (250 x 250 x 260 mm build volume, 600 mm/s max speed, direct drive extruder).
הגדרות Slicer
העתק את הערכים האלה ל-Slicer שלך (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| הגדרה | ערך | טווח |
|---|---|---|
| טמפרטורת חרירון | 238°C | 230-245°C |
| טמפרטורת משטח | 100°C | 90-110°C |
| חרירון בשכבה ראשונה | 243°C | +5°C above normal |
| משטח בשכבה ראשונה | 105°C | +5°C above normal |
| מהירות הדפסה | 45 mm/s | 40-50 mm/s |
| מהירות שכבה ראשונה | 20 mm/s | 25-50% of normal |
| מהירות דפנות | 34 mm/s | 70-80% of normal |
| מהירות תנועה | 75 mm/s | 120-150% of print speed |
| גובה שכבה | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| מספר דפנות | 2-3 | Perimeters/shells |
| שכבות עליונות/תחתונות | 3-4 | Solid layers |
| מאוורר קירור | 0-10% | From layer 2+ |
| מרחק נסיגה | 0.8-1.2 mm | Direct drive |
| מהירות נסיגה | 40 mm/s | Direct drive |
לפני שמדפיסים
פרופילי איכות הדפסה
Three presets for common use cases with HIPS on the Anycubic Kobra 3 Combo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 45 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 40 mm/s | 20-30% | Miniatures, display pieces, fine detail |
היצמדות למשטח
HIPS uses the same bed adhesion methods as ABS since it's typically printed alongside ABS. PEI sheets at high temperature work well. Use an enclosure.
מדריך כיוון טמפרטורה
Nozzle: 238°C
Range: 230-245°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 100°C
Range: 90-110°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
פתרון תקלות HIPS על Anycubic Kobra 3 Combo
טיפים מקצועיים ל-HIPS
HIPS is designed to pair with ABS -- use the same enclosure and bed temp as your ABS settings
D-Limonene is reusable but loses potency; replace when dissolution slows down significantly
A brief soak to loosen supports, then manual removal, saves solvent and time
HIPS can also be used as a standalone material -- it is lightweight and easy to paint
Much more moisture-resistant than PVA, making storage and handling easier
הגדרות תמיכות
HIPS is best used as a support material for ABS, dissolved in D-Limonene. For standalone HIPS prints, use tree or organic supports with 0.2mm interface gap.
Anycubic Kobra 3 Combo Specs
| Build Volume | 250 x 250 x 260 mm |
| Max Speed | 600 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
HIPS Properties
| Nozzle Range | 230-245°C |
| Bed Range | 90-110°C |
| Speed Range | 40-50 mm/s |
| Difficulty | intermediate |
| Drying | Not required |
| Enclosure | Recommended |
HIPS במבט מהיר
יתרונות
- Dissolves in D-Limonene (support material for ABS)
- Much cheaper than PVA ($20-25/kg)
- Low moisture sensitivity
- Can be used as standalone lightweight material
- Easy to paint and post-process
חסרונות
- Requires D-Limonene solvent
- Only pairs well with ABS
- Needs enclosure (same as ABS)
- Less common than PVA for support use
רוצה הגדרות AI מותאמות אישית?
תאר את ההגדרה המדויקת שלך ואת מה שאתה מדפיס. מומחה ה-AI של 3DSearch מייצר הגדרות סלייסר מותאמות עבור ה-Anycubic Kobra 3 Combo שלך עם HIPS תוך שניות.
נסה את 3DSearch →מקורות: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. הערכים חושבו ממפרטי הפילמנט וממגבלות החומרה של המדפסת.