PVA Settings for Voxelab Aquila X2
Recommended slicer settings for printing PVA on the Voxelab Aquila X2 (220 x 220 x 250 mm build volume, 180 mm/s max speed, Bowden extruder).
Slicer-Konfiguration
Kopiere diese Werte in deinen Slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Einstellung | Wert | Bereich |
|---|---|---|
| Düsentemperatur | 200°C | 185-215°C |
| Heizbetttemperatur | 55°C | 50-60°C |
| Erste Schicht Düse | 205°C | +5°C above normal |
| Erste Schicht Heizbett | 60°C | +5°C above normal |
| Druckgeschwindigkeit | 25 mm/s | 20-30 mm/s |
| Erste Schicht Geschwindigkeit | 15 mm/s | 25-50% of normal |
| Wandgeschwindigkeit | 19 mm/s | 70-80% of normal |
| Verfahrgeschwindigkeit | 45 mm/s | 120-150% of print speed |
| Schichthöhe | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Wandanzahl | 2-3 | Perimeters/shells |
| Oben/Unten Schichten | 3-4 | Solid layers |
| Kühlventilator | 100% | From layer 2+ |
| Rückzugsdistanz | 4-6 mm | Bowden |
| Rückzugsgeschwindigkeit | 40 mm/s | Bowden |
Vor dem Drucken
Druckqualität Profile
Three presets for common use cases with PVA on the Voxelab Aquila X2.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 30 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 25 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 20 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Haftung des Heizbetts
PVA haftet gut auf PEI-Blechen und Glasbetten. Die Haftung ist ähnlich wie PLA. PVA ist wasserlöslich, daher trockene Lagerung ist kritisch.
Temperatur-Abstimmungsanleitung
Nozzle: 200°C
Range: 185-215°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 55°C
Range: 50-60°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Fehlerbehebung PVA auf Voxelab Aquila X2
Pro-Tipps für PVA
PVA ist perfekt für lösliches Support-Material
Lagere streng trocken - PVA ist sehr hygroskopisch
Drucke bei 200-220°C, ähnlich wie PLA
Nach dem Druck lösche einfach mit Wasser auf um Support zu entfernen
Das Material kann mit PLA kombiniert werden für Support+Model Druck
Support-Einstellungen
PVA is itself a support material. Dissolve in warm water (up to 45°C) after printing. Set support interface Z-distance to 0mm for water-soluble supports.
Voxelab Aquila X2 Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 180 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 100°C |
| Extruder | Bowden |
PVA Properties
| Nozzle Range | 185-215°C |
| Bed Range | 50-60°C |
| Speed Range | 20-30 mm/s |
| Difficulty | intermediate |
| Drying | 50°C / 5h |
| Enclosure | Not needed |
PVA auf einen Blick
Stärken
- Water-soluble support material
- Leaves near-perfect supported surfaces
- Dissolves in tap water (2-12 hours)
- Best paired with PLA
- No manual support removal needed
Schwächen
- Extremely moisture sensitive (dissolves in water)
- Expensive (~$40-60/kg)
- Requires dual-extruder setup
- Must be stored in airtight container at all times
- Brittle when moisture-damaged
Möchtest du personalisierte KI-Einstellungen?
Beschreibe dein genaues Setup und was du druckst. 3DSearch's KI-Experte erzeugt in Sekunden individuelle Slicer-Einstellungen für deinen Voxelab Aquila X2 mit PVA.
3DSearch ausprobieren →Quellen: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Werte berechnet aus Filament-Spezifikationen und Drucker-Hardware-Limits.