Glow-in-the-dark PLA Settings for Voxelab Aquila X2
Recommended slicer settings for printing Glow-in-the-dark PLA on the Voxelab Aquila X2 (220 x 220 x 250 mm build volume, 180 mm/s max speed, Bowden extruder).
Slicer-Konfiguration
Kopiere diese Werte in deinen Slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Einstellung | Wert | Bereich |
|---|---|---|
| Düsentemperatur | 210°C | 195-225°C |
| Heizbetttemperatur | 55°C | 50-60°C |
| Erste Schicht Düse | 215°C | +5°C above normal |
| Erste Schicht Heizbett | 60°C | +5°C above normal |
| Druckgeschwindigkeit | 40 mm/s | 30-50 mm/s |
| Erste Schicht Geschwindigkeit | 15 mm/s | 25-50% of normal |
| Wandgeschwindigkeit | 30 mm/s | 70-80% of normal |
| Verfahrgeschwindigkeit | 75 mm/s | 120-150% of print speed |
| Schichthöhe | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Wandanzahl | 2-3 | Perimeters/shells |
| Oben/Unten Schichten | 3-4 | Solid layers |
| Kühlventilator | 100% | From layer 2+ |
| Rückzugsdistanz | 4-6 mm | Bowden |
| Rückzugsgeschwindigkeit | 40 mm/s | Bowden |
Vor dem Drucken
Druckqualität Profile
Three presets for common use cases with Glow-in-the-dark PLA on the Voxelab Aquila X2.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Haftung des Heizbetts
Glow-in-the-dark PLA haftet wie normales PLA. Die Phosphoreszenzpartikel beeinflussen die Adhäsion nicht. Verwende Standard-PEI oder andere normale Oberflächen.
Temperatur-Abstimmungsanleitung
Nozzle: 210°C
Range: 195-225°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 55°C
Range: 50-60°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Fehlerbehebung Glow-in-the-dark PLA auf Voxelab Aquila X2
Pro-Tipps für Glow-in-the-dark PLA
Glow-in-the-dark PLA braucht Lichteinfluß zur Aktivierung - belichtet das fertige Teil
Drucke bei ähnlichen Temperaturen wie normales PLA (200-220°C)
Die Leuchtkraft kann mit der Zeit schwächer werden - lagere aus dem Licht
Experimentiere mit Belichtungszeiten für optimale Helligkeit
Das Material ist ideal für Spielzeug, Dekoration und Sicherheitsmarkierungen
Support-Einstellungen
For prints requiring supports with Glow-in-the-dark PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Voxelab Aquila X2 Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 180 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 100°C |
| Extruder | Bowden |
Glow-in-the-dark PLA Properties
| Nozzle Range | 195-225°C |
| Bed Range | 50-60°C |
| Speed Range | 30-50 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
Glow-in-the-dark PLA auf einen Blick
Stärken
- Charges in light and glows in the dark
- Fun for decorative and safety items
- Prints like standard PLA
Schwächen
- Phosphorescent particles are abrasive — hardened nozzle required
- Limited to green/blue glow colors
- Glow fades over minutes without recharging
- Surface finish is slightly grainy
Möchtest du personalisierte KI-Einstellungen?
Beschreibe dein genaues Setup und was du druckst. 3DSearch's KI-Experte erzeugt in Sekunden individuelle Slicer-Einstellungen für deinen Voxelab Aquila X2 mit Glow-in-the-dark PLA.
3DSearch ausprobieren →Quellen: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Werte berechnet aus Filament-Spezifikationen und Drucker-Hardware-Limits.