Recycled PLA Settings for Voxelab Aquila X2
Recommended slicer settings for printing Recycled PLA on the Voxelab Aquila X2 (220 x 220 x 250 mm build volume, 180 mm/s max speed, Bowden extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 205°C | 190-220°C |
| درجة حرارة المنصة | 55°C | 50-60°C |
| الفوهة للطبقة الأولى | 210°C | +5°C above normal |
| المنصة للطبقة الأولى | 60°C | +5°C above normal |
| سرعة الطباعة | 40 mm/s | 30-50 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 30 mm/s | 70-80% of normal |
| سرعة الانتقال | 75 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 4-6 mm | Bowden |
| سرعة السحب | 40 mm/s | Bowden |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with Recycled PLA on the Voxelab Aquila X2.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
Recycled PLA adheres similarly to standard PLA. Use a clean PEI sheet or glass bed with glue stick. Quality varies between batches, so if adhesion is inconsistent, increase bed temperature by 5°C.
دليل ضبط درجة الحرارة
Nozzle: 205°C
Range: 190-220°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 55°C
Range: 50-60°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء Recycled PLA على Voxelab Aquila X2
نصائح احترافية لـ Recycled PLA
Recycled PLA is an eco-friendly choice that prints nearly identically to standard PLA
Quality varies more between brands than standard PLA -- find a good manufacturer and stick with them
Colors may be less vibrant than virgin PLA; this is normal for recycled material
Store like regular PLA: airtight container with desiccant when not in use
إعدادات الدعائم
For prints requiring supports with Recycled PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Voxelab Aquila X2 Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 180 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 100°C |
| Extruder | Bowden |
Recycled PLA Properties
| Nozzle Range | 190-220°C |
| Bed Range | 50-60°C |
| Speed Range | 30-50 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
Recycled PLA في لمحة
نقاط القوة
- Eco-friendly — made from recycled materials
- Similar properties to standard PLA
- Reduces plastic waste
- Good for non-critical parts
نقاط الضعف
- Color consistency may vary between batches
- Slightly lower strength than virgin PLA
- Limited color selection
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Voxelab Aquila X2 مع Recycled PLA خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.