PHA Settings for Voxelab Aquila X2
Recommended slicer settings for printing PHA on the Voxelab Aquila X2 (220 x 220 x 250 mm build volume, 180 mm/s max speed, Bowden extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 188°C | 175-200°C |
| درجة حرارة المنصة | 50°C | 40-60°C |
| الفوهة للطبقة الأولى | 193°C | +5°C above normal |
| المنصة للطبقة الأولى | 55°C | +5°C above normal |
| سرعة الطباعة | 35 mm/s | 25-45 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 26 mm/s | 70-80% of normal |
| سرعة الانتقال | 68 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 4-6 mm | Bowden |
| سرعة السحب | 40 mm/s | Bowden |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with PHA on the Voxelab Aquila X2.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 45 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 35 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 25 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
PHA (polyhydroxyalkanoate) adheres similarly to PLA. Use a clean PEI sheet or glass bed with glue stick at 50-60°C. PHA is biodegradable and slightly more flexible than PLA.
دليل ضبط درجة الحرارة
Nozzle: 188°C
Range: 175-200°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 50°C
Range: 40-60°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء PHA على Voxelab Aquila X2
نصائح احترافية لـ PHA
PHA is fully biodegradable and compostable -- a greener alternative to PLA
Print settings are very similar to PLA; start with PLA settings and adjust from there
PHA is slightly more flexible than PLA and less brittle on impact
Store in a cool, dry place; PHA biodegrades faster in humid environments
إعدادات الدعائم
For prints requiring supports with PHA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Voxelab Aquila X2 Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 180 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 100°C |
| Extruder | Bowden |
PHA Properties
| Nozzle Range | 175-200°C |
| Bed Range | 40-60°C |
| Speed Range | 25-45 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
PHA في لمحة
نقاط القوة
- Fully biodegradable in soil and marine environments
- Renewable bioplastic from bacterial fermentation
- Non-toxic and biocompatible
- Easier to print than PLA in some cases
نقاط الضعف
- Lower heat resistance than PLA (~55°C)
- More expensive than PLA
- Limited availability and color options
- Slower degradation rate than marketed
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Voxelab Aquila X2 مع PHA خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.