PETG Settings for Voxelab Aquila X2
Recommended slicer settings for printing PETG on the Voxelab Aquila X2 (220 x 220 x 250 mm build volume, 180 mm/s max speed, Bowden extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 240°C | 230-250°C |
| درجة حرارة المنصة | 85°C | 80-90°C |
| الفوهة للطبقة الأولى | 245°C | +5°C above normal |
| المنصة للطبقة الأولى | 90°C | +5°C above normal |
| سرعة الطباعة | 50 mm/s | 40-60 mm/s |
| سرعة الطبقة الأولى | 20 mm/s | 25-50% of normal |
| سرعة الجدران | 38 mm/s | 70-80% of normal |
| سرعة الانتقال | 90 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 30-50% | From layer 2+ |
| مسافة السحب | 4-6 mm | Bowden |
| سرعة السحب | 40 mm/s | Bowden |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with PETG on the Voxelab Aquila X2.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 60 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 50 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 40 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
PETG bonds extremely well to smooth PEI sheets -- sometimes too well. Use a textured PEI sheet or apply a thin layer of glue stick as a release agent on smooth PEI to prevent damage. On glass beds, always use glue stick (PETG can pull glass chips off). Let the bed cool completely before removing prints.
دليل ضبط درجة الحرارة
Nozzle: 240°C
Range: 230-250°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 85°C
Range: 80-90°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء PETG على Voxelab Aquila X2
نصائح احترافية لـ PETG
Dry your PETG before printing -- even a new spool left open overnight can absorb enough moisture to affect quality
Slow down the first layer to 15-20 mm/s for solid adhesion
Use a lower fan speed (30-50%) -- too much cooling weakens layer adhesion with PETG
If printing on smooth PEI, use glue stick as a release agent to prevent bed damage
PETG is an excellent all-around material once you dial in the settings
إعدادات الدعائم
For prints requiring supports with PETG, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Voxelab Aquila X2 Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 180 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 100°C |
| Extruder | Bowden |
PETG Properties
| Nozzle Range | 230-250°C |
| Bed Range | 80-90°C |
| Speed Range | 40-60 mm/s |
| Difficulty | beginner |
| Drying | 65°C / 7h |
| Enclosure | Not needed |
PETG في لمحة
نقاط القوة
- Excellent all-around material for functional parts
- Good impact resistance (much better than PLA)
- Moderate heat resistance (softens ~80C)
- FDA-approved for food contact in raw form
- Good chemical resistance
- Semi-flexible (bends before breaking)
نقاط الضعف
- Prone to stringing
- Moderate moisture sensitivity
- Can bond too strongly to glass beds
- Lower fan speeds required (not great for overhangs)
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Voxelab Aquila X2 مع PETG خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.