Conductive PLA Settings for Voxelab Aquila X2
Recommended slicer settings for printing Conductive PLA on the Voxelab Aquila X2 (220 x 220 x 250 mm build volume, 180 mm/s max speed, Bowden extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 215°C | 200-230°C |
| درجة حرارة المنصة | 55°C | 50-60°C |
| الفوهة للطبقة الأولى | 220°C | +5°C above normal |
| المنصة للطبقة الأولى | 60°C | +5°C above normal |
| سرعة الطباعة | 30 mm/s | 20-40 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 23 mm/s | 70-80% of normal |
| سرعة الانتقال | 60 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 4-6 mm | Bowden |
| سرعة السحب | 40 mm/s | Bowden |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with Conductive PLA on the Voxelab Aquila X2.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 40 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 30 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 20 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
Conductive PLA adheres like standard PLA. Use a clean PEI sheet or glass bed with glue stick. Handle prints carefully — the conductive carbon particles can leave residue on build surfaces.
دليل ضبط درجة الحرارة
Nozzle: 215°C
Range: 200-230°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 55°C
Range: 50-60°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء Conductive PLA على Voxelab Aquila X2
نصائح احترافية لـ Conductive PLA
Resistance varies with print orientation; Z-axis conductivity is lower than XY-axis
Print at consistent speed and temperature for the most uniform electrical properties
Best for capacitive touch sensors, LED circuits, and low-voltage applications
Not suitable for high-current applications; resistance is in the kOhm range per cm
إعدادات الدعائم
For prints requiring supports with Conductive PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Voxelab Aquila X2 Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 180 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 100°C |
| Extruder | Bowden |
Conductive PLA Properties
| Nozzle Range | 200-230°C |
| Bed Range | 50-60°C |
| Speed Range | 20-40 mm/s |
| Difficulty | intermediate |
| Drying | Not required |
| Enclosure | Not needed |
Conductive PLA في لمحة
نقاط القوة
- Electrically conductive — can create touch sensors
- Useful for prototyping simple circuits
- Prints on standard PLA settings
- Enables embedded electronics in prints
نقاط الضعف
- High resistance — not suitable for power circuits
- Conductivity varies with print orientation
- Limited to black color
- More expensive than standard PLA
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Voxelab Aquila X2 مع Conductive PLA خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.