CPE Settings for Monoprice Maker Select V2
Recommended slicer settings for printing CPE on the Monoprice Maker Select V2 (200 x 200 x 180 mm build volume, 150 mm/s max speed, Bowden extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 255°C | 240-270°C |
| درجة حرارة المنصة | 83°C | 75-90°C |
| الفوهة للطبقة الأولى | 260°C | +5°C above normal |
| المنصة للطبقة الأولى | 88°C | +5°C above normal |
| سرعة الطباعة | 40 mm/s | 30-50 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 30 mm/s | 70-80% of normal |
| سرعة الانتقال | 75 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 4-6 mm | Bowden |
| سرعة السحب | 40 mm/s | Bowden |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with CPE on the Monoprice Maker Select V2.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
CPE (co-polyester) adheres similarly to PETG. Use a textured PEI sheet at 75-85°C or smooth PEI with glue stick as a release agent. Let the bed cool completely before removing prints.
دليل ضبط درجة الحرارة
Nozzle: 255°C
Range: 240-270°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 83°C
Range: 75-90°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء CPE على Monoprice Maker Select V2
نصائح احترافية لـ CPE
CPE is Ultimaker's co-polyester; it prints very similarly to PETG
Dry at 70°C for 6-8 hours before printing for best results
Use a textured PEI sheet; CPE can bond too strongly to smooth PEI
CPE is FDA-approved for food contact -- good for food-safe containers
إعدادات الدعائم
For prints requiring supports with CPE, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Monoprice Maker Select V2 Specs
| Build Volume | 200 x 200 x 180 mm |
| Max Speed | 150 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 100°C |
| Extruder | Bowden |
CPE Properties
| Nozzle Range | 240-270°C |
| Bed Range | 75-90°C |
| Speed Range | 30-50 mm/s |
| Difficulty | intermediate |
| Drying | 60°C / 6h |
| Enclosure | Not needed |
CPE في لمحة
نقاط القوة
- Excellent chemical resistance
- Higher heat resistance than PETG (~100°C)
- Good toughness and impact resistance
- FDA-compliant grades available
نقاط الضعف
- More difficult to print than PETG
- Higher temperatures required
- More prone to stringing
- Limited brand availability
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Monoprice Maker Select V2 مع CPE خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.