Glass-fiber PETG Settings for Monoprice Maker Select V2
Recommended slicer settings for printing Glass-fiber PETG on the Monoprice Maker Select V2 (200 x 200 x 180 mm build volume, 150 mm/s max speed, Bowden extruder).
Slicer Configuration
Copy these values into your slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Setting | Value | Range |
|---|---|---|
| Nozzle Temperature | 248°C | 235-260°C |
| Bed Temperature | 88°C | 80-95°C |
| First Layer Nozzle | 253°C | +5°C above normal |
| First Layer Bed | 93°C | +5°C above normal |
| Print Speed | 40 mm/s | 30-50 mm/s |
| First Layer Speed | 15 mm/s | 25-50% of normal |
| Wall Speed | 30 mm/s | 70-80% of normal |
| Travel Speed | 75 mm/s | 120-150% of print speed |
| Layer Height | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Wall Count | 2-3 | Perimeters/shells |
| Top/Bottom Layers | 3-4 | Solid layers |
| Cooling Fan | 100% | From layer 2+ |
| Retraction Distance | 4-6 mm | Bowden |
| Retraction Speed | 40 mm/s | Bowden |
Before You Print
Print Quality Profiles
Three presets for common use cases with Glass-fiber PETG on the Monoprice Maker Select V2.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Bed Adhesion
Glass-fiber PETG adheres like standard PETG. Use a textured PEI sheet or glue stick on smooth PEI as a release agent. The glass fibers reduce warping compared to plain PETG. A hardened steel nozzle is required.
Temperature Tuning Guide
Nozzle: 248°C
Range: 235-260°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 88°C
Range: 80-95°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Troubleshooting Glass-fiber PETG on Monoprice Maker Select V2
Pro Tips for Glass-fiber PETG
Hardened steel nozzle (0.5mm+) is mandatory -- glass fibers are even more abrasive than carbon fibers
Dry thoroughly at 65°C for 8 hours before printing
Print 30% slower than plain PETG for best surface quality
Glass-fiber PETG is stiffer than carbon-fiber PETG but slightly less strong; good for dimensional stability
Support Settings
For prints requiring supports with Glass-fiber PETG, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Monoprice Maker Select V2 Specs
| Build Volume | 200 x 200 x 180 mm |
| Max Speed | 150 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 100°C |
| Extruder | Bowden |
Glass-fiber PETG Properties
| Nozzle Range | 235-260°C |
| Bed Range | 80-95°C |
| Speed Range | 30-50 mm/s |
| Difficulty | intermediate |
| Drying | 65°C / 7h |
| Enclosure | Not needed |
Glass-fiber PETG at a Glance
Strengths
- Much stiffer than standard PETG
- Better heat resistance than plain PETG
- Good dimensional stability
- Less expensive than carbon fiber composites
Weaknesses
- Hardened steel nozzle required
- Increased brittleness vs standard PETG
- Use 0.5mm+ nozzle to prevent clogging
- Rougher surface finish
Want personalized AI settings?
Describe your exact setup and what you are printing. 3DSearch's AI expert generates custom slicer settings for your Monoprice Maker Select V2 with Glass-fiber PETG in seconds.
Try 3DSearch →Sources: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Values calculated from filament specifications and printer hardware limits.