PC Settings for Bambu Lab X1 Carbon
Recommended slicer settings for printing PC on the Bambu Lab X1 Carbon (256 x 256 x 256 mm build volume, 500 mm/s max speed, direct drive extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 285°C | 260-310°C |
| درجة حرارة المنصة | 110°C | 100-120°C |
| الفوهة للطبقة الأولى | 290°C | +5°C above normal |
| المنصة للطبقة الأولى | 115°C | +5°C above normal |
| سرعة الطباعة | 30 mm/s | 20-40 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 23 mm/s | 70-80% of normal |
| سرعة الانتقال | 60 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 0-10% | From layer 2+ |
| مسافة السحب | 0.8-1.2 mm | Direct drive |
| سرعة السحب | 40 mm/s | Direct drive |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with PC on the Bambu Lab X1 Carbon.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 40 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 30 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 20 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
Polycarbonate needs very high bed temperatures and excellent adhesion. Use a PEI sheet at maximum bed temperature. Apply glue stick as a release agent (PC can bond too strongly). A brim is essential. Consider Magigoo PC specialty adhesive for best results.
دليل ضبط درجة الحرارة
Nozzle: 285°C
Range: 260-310°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 110°C
Range: 100-120°C. Printer max: 120°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء PC على Bambu Lab X1 Carbon
نصائح احترافية لـ PC
PC is the most demanding common filament to print -- make sure your setup is fully prepared
An all-metal hotend is mandatory; PTFE-lined hotends will degrade at PC temperatures
Seal your enclosure as thoroughly as possible for the best results
Use glue stick as a release agent -- PC can bond so strongly to PEI that it damages the sheet
If you are new to high-temp printing, try ABS or ASA first before attempting polycarbonate
إعدادات الدعائم
For prints requiring supports with PC, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Bambu Lab X1 Carbon Specs
| Build Volume | 256 x 256 x 256 mm |
| Max Speed | 500 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 120°C |
| Extruder | Direct Drive |
PC Properties
| Nozzle Range | 260-310°C |
| Bed Range | 100-120°C |
| Speed Range | 20-40 mm/s |
| Difficulty | advanced |
| Drying | 80°C / 10h |
| Enclosure | Recommended |
PC في لمحة
نقاط القوة
- Arguably the toughest non-flexible filament
- Excellent heat resistance (softens ~150C)
- Can withstand repeated impacts without shattering
- Can print in translucent/clear
- Ideal for protective equipment and high-temp parts
نقاط الضعف
- Requires all-metal hotend
- Severe warping without heated enclosure
- Very high printing temperatures
- High moisture sensitivity
- Most demanding common filament to print
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Bambu Lab X1 Carbon مع PC خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on Bambu Lab Wiki (wiki.bambulab.com), community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.