HIPS Settings for Anycubic Kobra 3 Combo
Recommended slicer settings for printing HIPS on the Anycubic Kobra 3 Combo (250 x 250 x 260 mm build volume, 600 mm/s max speed, direct drive extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 238°C | 230-245°C |
| درجة حرارة المنصة | 100°C | 90-110°C |
| الفوهة للطبقة الأولى | 243°C | +5°C above normal |
| المنصة للطبقة الأولى | 105°C | +5°C above normal |
| سرعة الطباعة | 45 mm/s | 40-50 mm/s |
| سرعة الطبقة الأولى | 20 mm/s | 25-50% of normal |
| سرعة الجدران | 34 mm/s | 70-80% of normal |
| سرعة الانتقال | 75 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 0-10% | From layer 2+ |
| مسافة السحب | 0.8-1.2 mm | Direct drive |
| سرعة السحب | 40 mm/s | Direct drive |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with HIPS on the Anycubic Kobra 3 Combo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 45 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 40 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
HIPS uses the same bed adhesion methods as ABS since it's typically printed alongside ABS. PEI sheets at high temperature work well. Use an enclosure.
دليل ضبط درجة الحرارة
Nozzle: 238°C
Range: 230-245°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 100°C
Range: 90-110°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء HIPS على Anycubic Kobra 3 Combo
نصائح احترافية لـ HIPS
HIPS is designed to pair with ABS -- use the same enclosure and bed temp as your ABS settings
D-Limonene is reusable but loses potency; replace when dissolution slows down significantly
A brief soak to loosen supports, then manual removal, saves solvent and time
HIPS can also be used as a standalone material -- it is lightweight and easy to paint
Much more moisture-resistant than PVA, making storage and handling easier
إعدادات الدعائم
HIPS is best used as a support material for ABS, dissolved in D-Limonene. For standalone HIPS prints, use tree or organic supports with 0.2mm interface gap.
Anycubic Kobra 3 Combo Specs
| Build Volume | 250 x 250 x 260 mm |
| Max Speed | 600 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
HIPS Properties
| Nozzle Range | 230-245°C |
| Bed Range | 90-110°C |
| Speed Range | 40-50 mm/s |
| Difficulty | intermediate |
| Drying | Not required |
| Enclosure | Recommended |
HIPS في لمحة
نقاط القوة
- Dissolves in D-Limonene (support material for ABS)
- Much cheaper than PVA ($20-25/kg)
- Low moisture sensitivity
- Can be used as standalone lightweight material
- Easy to paint and post-process
نقاط الضعف
- Requires D-Limonene solvent
- Only pairs well with ABS
- Needs enclosure (same as ABS)
- Less common than PVA for support use
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Anycubic Kobra 3 Combo مع HIPS خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.