Breakaway Support Settings for Anycubic Kobra 3 Combo
Recommended slicer settings for printing Breakaway Support on the Anycubic Kobra 3 Combo (250 x 250 x 260 mm build volume, 600 mm/s max speed, direct drive extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 225°C | 210-240°C |
| درجة حرارة المنصة | 60°C | 50-70°C |
| الفوهة للطبقة الأولى | 230°C | +5°C above normal |
| المنصة للطبقة الأولى | 65°C | +5°C above normal |
| سرعة الطباعة | 40 mm/s | 30-50 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 30 mm/s | 70-80% of normal |
| سرعة الانتقال | 75 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 0.8-1.2 mm | Direct drive |
| سرعة السحب | 40 mm/s | Direct drive |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with Breakaway Support on the Anycubic Kobra 3 Combo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
Breakaway support material adheres to whatever build surface your main material uses. Bed temperature should match the main filament. After printing, snap off supports mechanically — no solvents needed.
دليل ضبط درجة الحرارة
Nozzle: 225°C
Range: 210-240°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 60°C
Range: 50-70°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء Breakaway Support على Anycubic Kobra 3 Combo
نصائح احترافية لـ Breakaway Support
Breakaway supports snap off mechanically -- no solvents or water required
Adjust Z-gap and interface density to balance support strength vs. ease of removal
Breakaway is faster to remove than soluble supports like PVA/BVOH for simple overhangs
Use soluble supports instead for complex internal geometries where mechanical access is difficult
إعدادات الدعائم
For prints requiring supports with Breakaway Support, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 3 Combo Specs
| Build Volume | 250 x 250 x 260 mm |
| Max Speed | 600 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
Breakaway Support Properties
| Nozzle Range | 210-240°C |
| Bed Range | 50-70°C |
| Speed Range | 30-50 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
Breakaway Support في لمحة
نقاط القوة
- Snaps off cleanly without solvents
- Fast removal — no dissolving wait time
- Works with most build materials
- No special post-processing needed
نقاط الضعف
- Leaves rougher surface than dissolved supports
- Requires accessible support geometry
- Not suitable for internal cavities
- May need pliers for tight areas
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Anycubic Kobra 3 Combo مع Breakaway Support خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.