PLA Settings for Creality CR-10 Smart Pro
Recommended slicer settings for printing PLA on the Creality CR-10 Smart Pro (300 x 300 x 400 mm build volume, 100 mm/s max speed, direct drive extruder).
切片配置
将这些参数复制到你的切片软件（Cura、OrcaSlicer、PrusaSlicer、Bambu Studio）| 参数 | 数值 | 范围 |
|---|---|---|
| 喷嘴温度 | 205°C | 190-220°C |
| 热床温度 | 55°C | 50-60°C |
| 首层喷嘴 | 210°C | +5°C above normal |
| 首层热床 | 60°C | +5°C above normal |
| 打印速度 | 50 mm/s | 40-60 mm/s |
| 首层速度 | 20 mm/s | 25-50% of normal |
| 外壁速度 | 38 mm/s | 70-80% of normal |
| 空走速度 | 90 mm/s | 120-150% of print speed |
| 层高 | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| 壁数 | 2-3 | Perimeters/shells |
| 顶层/底层 | 3-4 | Solid layers |
| 散热风扇 | 100% | From layer 2+ |
| 回抽距离 | 0.8-1.2 mm | Direct drive |
| 回抽速度 | 40 mm/s | Direct drive |
开始打印前
打印质量预设
Three presets for common use cases with PLA on the Creality CR-10 Smart Pro.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 60 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 50 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 40 mm/s | 20-30% | Miniatures, display pieces, fine detail |
热床附着
PLA 在 PEI 片上粘合良好(光滑或有纹理),无需粘合剂。如果使用玻璃热床,涂上薄层胶棒或发胶。每次打印前用异丙醇(IPA)清洁热床以保持一致粘合。
温度调校指南
Nozzle: 205°C
Range: 190-220°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 55°C
Range: 50-60°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
在 Creality CR-10 Smart Pro 上打印 PLA 的问题排查
PLA 使用技巧
打印温度塔找到你特定 PLA 品牌的最佳温度
不使用时将耗材储存在密闭容器中,配合干燥剂
每次打印前用 IPA 清洁热床以保持一致粘合
从第 2 层开始使用 100% 冷却风扇,以获得最佳悬垂和桥接
PLA 适合原型设计,但避免将打印件放在炎热的汽车或直射阳光下
支撑设置
For prints requiring supports with PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Creality CR-10 Smart Pro Specs
| Build Volume | 300 x 300 x 400 mm |
| Max Speed | 100 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 100°C |
| Extruder | Direct Drive |
PLA Properties
| Nozzle Range | 190-220°C |
| Bed Range | 50-60°C |
| Speed Range | 40-60 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
PLA 速览
优势
- Easiest filament to print with
- No heated bed strictly required (helps though)
- Wide range of colors available
- Low warping
- Biodegradable (derived from corn starch)
- Good tensile strength (47-60 MPa)
劣势
- Low heat resistance (softens at 55-60C)
- Brittle under impact
- Poor UV/outdoor resistance
- Not food-safe without coating
想要个性化的 AI 参数？
描述你的具体配置和要打印的内容。3DSearch 的 AI 专家会在几秒内为你的 Creality CR-10 Smart Pro 搭配 PLA 生成定制切片参数。
试用 3DSearch →来源： Based on Creality support documentation, community testing data, manufacturer recommended ranges. 参数根据耗材规格和打印机硬件上限计算得出。