PETG-CF Settings for Creality CR-10 SE
Recommended slicer settings for printing PETG-CF on the Creality CR-10 SE (220 x 220 x 265 mm build volume, 600 mm/s max speed, direct drive extruder).
切片配置
将这些参数复制到你的切片软件（Cura、OrcaSlicer、PrusaSlicer、Bambu Studio）| 参数 | 数值 | 范围 |
|---|---|---|
| 喷嘴温度 | 245°C | 230-260°C |
| 热床温度 | 75°C | 70-80°C |
| 首层喷嘴 | 250°C | +5°C above normal |
| 首层热床 | 80°C | +5°C above normal |
| 打印速度 | 40 mm/s | 30-50 mm/s |
| 首层速度 | 15 mm/s | 25-50% of normal |
| 外壁速度 | 30 mm/s | 70-80% of normal |
| 空走速度 | 75 mm/s | 120-150% of print speed |
| 层高 | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| 壁数 | 2-3 | Perimeters/shells |
| 顶层/底层 | 3-4 | Solid layers |
| 散热风扇 | 30-50% | From layer 2+ |
| 回抽距离 | 0.8-1.2 mm | Direct drive |
| 回抽速度 | 40 mm/s | Direct drive |
开始打印前
打印质量预设
Three presets for common use cases with PETG-CF on the Creality CR-10 SE.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
热床附着
PETG-CF 与标准 PETG 粘合类似。在光滑 PEI 上使用有纹理的 PEI 片或涂胶棒作为脱模剂。碳纤维与普通 PETG 相比减少翘曲,因此粘合通常更容易。移除打印件前让热床完全冷却。
温度调校指南
Nozzle: 245°C
Range: 230-260°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 75°C
Range: 70-80°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
在 Creality CR-10 SE 上打印 PETG-CF 的问题排查
PETG-CF 使用技巧
硬化钢喷嘴是强制的 -- 从不用黄铜做碳纤维耗材
使用 0.5mm 或 0.6mm 喷嘴以获得最佳可靠性和流量
每次使用前干燥 PETG-CF -- 水分导致起泡和削弱碳纤维粘合
比普通 PETG 慢 30-40% 打印以获得最佳表面质量和纤维排列
PETG-CF 在需要刚性而无尼龙-CF 高温的功能零件上表现出色
支撑设置
For prints requiring supports with PETG-CF, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Creality CR-10 SE Specs
| Build Volume | 220 x 220 x 265 mm |
| Max Speed | 600 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 100°C |
| Extruder | Direct Drive |
PETG-CF Properties
| Nozzle Range | 230-260°C |
| Bed Range | 70-80°C |
| Speed Range | 30-50 mm/s |
| Difficulty | intermediate |
| Drying | 65°C / 8h |
| Enclosure | Not needed |
PETG-CF 速览
优势
- Significantly stiffer than standard PETG
- Professional matte surface finish
- Reduced warping compared to plain PETG
- Good chemical and moisture resistance
- Excellent for functional brackets, jigs, and fixtures
劣势
- Requires hardened steel nozzle (carbon fibers destroy brass)
- More brittle than standard PETG (reduced flexibility)
- Must use 0.5mm+ nozzle to prevent clogging
- Slower print speeds required than standard PETG
- Higher cost than plain PETG ($30-45/kg)
想要个性化的 AI 参数？
描述你的具体配置和要打印的内容。3DSearch 的 AI 专家会在几秒内为你的 Creality CR-10 SE 搭配 PETG-CF 生成定制切片参数。
试用 3DSearch →来源： Based on Creality support documentation, community testing data, manufacturer recommended ranges. 参数根据耗材规格和打印机硬件上限计算得出。