Carbon Fiber PLA Settings for Creality CR-10 SE
Recommended slicer settings for printing Carbon Fiber PLA on the Creality CR-10 SE (220 x 220 x 265 mm build volume, 600 mm/s max speed, direct drive extruder).
Slicer Configuration
Copy these values into your slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Setting | Value | Range |
|---|---|---|
| Nozzle Temperature | 215°C | 200-230°C |
| Bed Temperature | 58°C | 50-65°C |
| First Layer Nozzle | 220°C | +5°C above normal |
| First Layer Bed | 63°C | +5°C above normal |
| Print Speed | 40 mm/s | 30-50 mm/s |
| First Layer Speed | 15 mm/s | 25-50% of normal |
| Wall Speed | 30 mm/s | 70-80% of normal |
| Travel Speed | 75 mm/s | 120-150% of print speed |
| Layer Height | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Wall Count | 2-3 | Perimeters/shells |
| Top/Bottom Layers | 3-4 | Solid layers |
| Cooling Fan | 100% | From layer 2+ |
| Retraction Distance | 0.8-1.2 mm | Direct drive |
| Retraction Speed | 40 mm/s | Direct drive |
Before You Print
Print Quality Profiles
Three presets for common use cases with Carbon Fiber PLA on the Creality CR-10 SE.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Bed Adhesion
Carbon Fiber PLA adheres similarly to regular PLA. A clean PEI sheet works well. For glass beds, use glue stick. The carbon fibers reduce warping compared to regular PLA.
Temperature Tuning Guide
Nozzle: 215°C
Range: 200-230°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 58°C
Range: 50-65°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Troubleshooting Carbon Fiber PLA on Creality CR-10 SE
Pro Tips for Carbon Fiber PLA
A hardened steel nozzle is mandatory -- do not print CF PLA with a brass nozzle
Use a 0.5mm or 0.6mm nozzle for the most reliable printing with carbon fibers
Print 25-50% slower than regular PLA to reduce stress on the extruder and improve quality
CF PLA excels in stiffness and rigidity -- ideal for structural parts, not impact-resistant ones
The matte finish looks professional and hides layer lines better than glossy filaments
Support Settings
For prints requiring supports with Carbon Fiber PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Creality CR-10 SE Specs
| Build Volume | 220 x 220 x 265 mm |
| Max Speed | 600 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 100°C |
| Extruder | Direct Drive |
Carbon Fiber PLA Properties
| Nozzle Range | 200-230°C |
| Bed Range | 50-65°C |
| Speed Range | 30-50 mm/s |
| Difficulty | intermediate |
| Drying | Not required |
| Enclosure | Not needed |
Carbon Fiber PLA at a Glance
Strengths
- Much stiffer than regular PLA
- Reduced warping compared to PLA
- Professional matte surface finish
- Ideal for drone frames, brackets, fixtures
- Lightweight with structural rigidity
Weaknesses
- Requires hardened steel nozzle (destroys brass)
- More brittle than regular PLA
- 25-50% slower print speeds needed
- Does not add tensile strength (short fibers)
- Use 0.5mm+ nozzle to prevent clogging
Want personalized AI settings?
Describe your exact setup and what you are printing. 3DSearch's AI expert generates custom slicer settings for your Creality CR-10 SE with Carbon Fiber PLA in seconds.
Try 3DSearch →Sources: Based on Creality support documentation, community testing data, manufacturer recommended ranges. Values calculated from filament specifications and printer hardware limits.