HIPS Settings for Bambu Lab A1
Recommended slicer settings for printing HIPS on the Bambu Lab A1 (256 x 256 x 256 mm build volume, 500 mm/s max speed, direct drive extruder).
切片配置
将这些参数复制到你的切片软件（Cura、OrcaSlicer、PrusaSlicer、Bambu Studio）| 参数 | 数值 | 范围 |
|---|---|---|
| 喷嘴温度 | 238°C | 230-245°C |
| 热床温度 | 100°C | 90-110°C |
| 首层喷嘴 | 243°C | +5°C above normal |
| 首层热床 | 100°C | At printer max |
| 打印速度 | 45 mm/s | 40-50 mm/s |
| 首层速度 | 20 mm/s | 25-50% of normal |
| 外壁速度 | 34 mm/s | 70-80% of normal |
| 空走速度 | 75 mm/s | 120-150% of print speed |
| 层高 | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| 壁数 | 2-3 | Perimeters/shells |
| 顶层/底层 | 3-4 | Solid layers |
| 散热风扇 | 0-10% | From layer 2+ |
| 回抽距离 | 0.8-1.2 mm | Direct drive |
| 回抽速度 | 40 mm/s | Direct drive |
开始打印前
打印质量预设
Three presets for common use cases with HIPS on the Bambu Lab A1.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 45 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 40 mm/s | 20-30% | Miniatures, display pieces, fine detail |
热床附着
HIPS 使用与 ABS 相同的热床粘合方法,因为它通常与 ABS 一起打印。高温 PEI 片效果良好。使用外罩。
温度调校指南
Nozzle: 238°C
Range: 230-245°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 100°C
Range: 90-110°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
在 Bambu Lab A1 上打印 HIPS 的问题排查
HIPS 使用技巧
HIPS 设计用于配对 ABS -- 使用与你的 ABS 设置相同的外罩和热床温度
D-Limonene 可重复使用但随时间失效;当溶解明显变慢时更换
简单浸泡以松动支撑,然后手动移除,节省溶剂和时间
HIPS 也可作为独立材料使用 -- 它质轻且易于涂漆
比 PVA 防水性强得多,使储存和处理更容易
支撑设置
HIPS is best used as a support material for ABS, dissolved in D-Limonene. For standalone HIPS prints, use tree or organic supports with 0.2mm interface gap.
Bambu Lab A1 Specs
| Build Volume | 256 x 256 x 256 mm |
| Max Speed | 500 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 100°C |
| Extruder | Direct Drive |
HIPS Properties
| Nozzle Range | 230-245°C |
| Bed Range | 90-110°C |
| Speed Range | 40-50 mm/s |
| Difficulty | intermediate |
| Drying | Not required |
| Enclosure | Recommended |
HIPS 速览
优势
- Dissolves in D-Limonene (support material for ABS)
- Much cheaper than PVA ($20-25/kg)
- Low moisture sensitivity
- Can be used as standalone lightweight material
- Easy to paint and post-process
劣势
- Requires D-Limonene solvent
- Only pairs well with ABS
- Needs enclosure (same as ABS)
- Less common than PVA for support use
想要个性化的 AI 参数？
描述你的具体配置和要打印的内容。3DSearch 的 AI 专家会在几秒内为你的 Bambu Lab A1 搭配 HIPS 生成定制切片参数。
试用 3DSearch →来源： Based on Bambu Lab Wiki (wiki.bambulab.com), community testing data, manufacturer recommended ranges. 参数根据耗材规格和打印机硬件上限计算得出。