PA6 Settings for Anycubic Kobra 2 Neo
Recommended slicer settings for printing PA6 on the Anycubic Kobra 2 Neo (220 x 220 x 250 mm build volume, 250 mm/s max speed, direct drive extruder).
Slicer Yapılandırması
Bu değerleri slicer'ına (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio) kopyala| Ayar | Değer | Aralık |
|---|---|---|
| Nozzle Sıcaklığı | 255°C | 240-270°C |
| Platform Sıcaklığı | 90°C | 80-100°C |
| İlk Katman Nozzle | 260°C | +5°C above normal |
| İlk Katman Platform | 95°C | +5°C above normal |
| Baskı Hızı | 40 mm/s | 30-50 mm/s |
| İlk Katman Hızı | 15 mm/s | 25-50% of normal |
| Duvar Hızı | 30 mm/s | 70-80% of normal |
| Hareket Hızı | 75 mm/s | 120-150% of print speed |
| Katman Yüksekliği | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Duvar Sayısı | 2-3 | Perimeters/shells |
| Üst/Alt Katmanlar | 3-4 | Solid layers |
| Soğutma Vantilatörü | 100% | From layer 2+ |
| Geri Çekilme Mesafesi | 0.8-1.2 mm | Direct drive |
| Geri Çekilme Hızı | 40 mm/s | Direct drive |
Yazdırmadan Önce
Baskı Kalitesi Profilleri
Three presets for common use cases with PA6 on the Anycubic Kobra 2 Neo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Platform Yapışması
PA6 (Polyamid 6) PA12'ye benzer şekilde yapışır ancak daha iyi yapışma ile. Glue stick ile dokulu PEI veya Garolite kullan. Etek önerilir.
Sıcaklık Ayarlama Rehberi
Nozzle: 255°C
Range: 240-270°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 90°C
Range: 80-100°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
PA6 ile Anycubic Kobra 2 Neo üzerinde sorun giderme
PA6 için Pro İpuçları
PA6, 255-270°C gerektirir - PA12'den daha yüksek
Dokulu veya işlenen yatak neredeyse zorunludur
Daha iyi yapışma için etek yazdır
PA6 higroskopiktir - yazmadan önce en az 4 saat kurut
PA6 PA12'den daha sağlam ve esnektir
Destek Ayarları
For prints requiring supports with PA6, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 2 Neo Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 250 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
PA6 Properties
| Nozzle Range | 240-270°C |
| Bed Range | 80-100°C |
| Speed Range | 30-50 mm/s |
| Difficulty | advanced |
| Drying | 85°C / 12h |
| Enclosure | Recommended |
PA6 Bir Bakışta
Güçlü Yönleri
- Strongest common nylon variant
- Exceptional wear and fatigue resistance
- Good chemical resistance
- Excellent for gears, bearings, hinges
Zayıf Yönleri
- Extremely hygroscopic — must dry extensively
- Warps aggressively without enclosure
- Difficult bed adhesion
- Shrinks significantly during cooling
Kişiselleştirilmiş yapay zeka ayarları ister misin?
Tam kurulumunu ve ne yazdırdığını açıkla. 3DSearch'ün yapay zeka uzmanı saniyeler içinde PA6 ile Anycubic Kobra 2 Neo için özel slicer ayarları oluşturuyor.
3DSearch'ü dene →Kaynaklar: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Değerler filament belirtimleri ve yazıcı donanım sınırlarından hesaplanmıştır.