Matte PLA Settings for Anycubic Kobra 2 Neo
Recommended slicer settings for printing Matte PLA on the Anycubic Kobra 2 Neo (220 x 220 x 250 mm build volume, 250 mm/s max speed, direct drive extruder).
Slicer Yapılandırması
Bu değerleri slicer'ına (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio) kopyala| Ayar | Değer | Aralık |
|---|---|---|
| Nozzle Sıcaklığı | 210°C | 195-225°C |
| Platform Sıcaklığı | 58°C | 50-65°C |
| İlk Katman Nozzle | 215°C | +5°C above normal |
| İlk Katman Platform | 63°C | +5°C above normal |
| Baskı Hızı | 50 mm/s | 40-60 mm/s |
| İlk Katman Hızı | 20 mm/s | 25-50% of normal |
| Duvar Hızı | 38 mm/s | 70-80% of normal |
| Hareket Hızı | 90 mm/s | 120-150% of print speed |
| Katman Yüksekliği | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Duvar Sayısı | 2-3 | Perimeters/shells |
| Üst/Alt Katmanlar | 3-4 | Solid layers |
| Soğutma Vantilatörü | 100% | From layer 2+ |
| Geri Çekilme Mesafesi | 0.8-1.2 mm | Direct drive |
| Geri Çekilme Hızı | 40 mm/s | Direct drive |
Yazdırmadan Önce
Baskı Kalitesi Profilleri
Three presets for common use cases with Matte PLA on the Anycubic Kobra 2 Neo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 60 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 50 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 40 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Platform Yapışması
Mat PLA normal PLA gibi yapışır. Mat yüzey özelliği yapışmayı etkilemez. Standart PEI veya diğer normal yöntemler kullan.
Sıcaklık Ayarlama Rehberi
Nozzle: 210°C
Range: 195-225°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 58°C
Range: 50-65°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Matte PLA ile Anycubic Kobra 2 Neo üzerinde sorun giderme
Matte PLA için Pro İpuçları
Mat PLA, temiz, parlak olmayan görünüm gerektiren parçalar için idealdir
Normal PLA'ya benzer sıcaklıklarda yazdır (200-220°C)
Mat yüzey özelliği doğaldır - son işlem gerekli değildir
Mat bitişi, parlak PLA'dan daha iyi katman çizgilerini gizler
Normal PLA gibi kapalı kapta sakla
Destek Ayarları
For prints requiring supports with Matte PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 2 Neo Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 250 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
Matte PLA Properties
| Nozzle Range | 195-225°C |
| Bed Range | 50-65°C |
| Speed Range | 40-60 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
Matte PLA Bir Bakışta
Güçlü Yönleri
- Beautiful non-reflective matte surface finish
- Hides layer lines better than standard PLA
- Same ease of printing as PLA
- Available in wide color range
Zayıf Yönleri
- Slightly weaker than standard PLA
- Surface scratches more visibly
- More expensive than regular PLA
Kişiselleştirilmiş yapay zeka ayarları ister misin?
Tam kurulumunu ve ne yazdırdığını açıkla. 3DSearch'ün yapay zeka uzmanı saniyeler içinde Matte PLA ile Anycubic Kobra 2 Neo için özel slicer ayarları oluşturuyor.
3DSearch'ü dene →Kaynaklar: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Değerler filament belirtimleri ve yazıcı donanım sınırlarından hesaplanmıştır.