PVA Settings for Bambu Lab H2D Pro
Recommended slicer settings for printing PVA on the Bambu Lab H2D Pro (350 x 320 x 325 mm build volume, 1000 mm/s max speed, direct drive extruder).
Slicer Yapılandırması
Bu değerleri slicer'ına (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio) kopyala| Ayar | Değer | Aralık |
|---|---|---|
| Nozzle Sıcaklığı | 200°C | 185-215°C |
| Platform Sıcaklığı | 55°C | 50-60°C |
| İlk Katman Nozzle | 205°C | +5°C above normal |
| İlk Katman Platform | 60°C | +5°C above normal |
| Baskı Hızı | 25 mm/s | 20-30 mm/s |
| İlk Katman Hızı | 15 mm/s | 25-50% of normal |
| Duvar Hızı | 19 mm/s | 70-80% of normal |
| Hareket Hızı | 45 mm/s | 120-150% of print speed |
| Katman Yüksekliği | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Duvar Sayısı | 2-3 | Perimeters/shells |
| Üst/Alt Katmanlar | 3-4 | Solid layers |
| Soğutma Vantilatörü | 100% | From layer 2+ |
| Geri Çekilme Mesafesi | 0.8-1.2 mm | Direct drive |
| Geri Çekilme Hızı | 40 mm/s | Direct drive |
Yazdırmadan Önce
Baskı Kalitesi Profilleri
Three presets for common use cases with PVA on the Bambu Lab H2D Pro.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 30 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 25 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 20 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Platform Yapışması
PVA PEI levhalarına ve cam yatağa iyi yapışır. Yapışma PLA'ya benzer. PVA su çözünür olduğundan kuru depolama kritiktir.
Sıcaklık Ayarlama Rehberi
Nozzle: 200°C
Range: 185-215°C. Printer max: 350°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 55°C
Range: 50-60°C. Printer max: 120°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
PVA ile Bambu Lab H2D Pro üzerinde sorun giderme
PVA için Pro İpuçları
PVA çözülebilir destek malzemesi için idealdir
Kesinlikle kuru sakla - PVA çok higroskopiktir
PLA'ya benzer 200-220°C'de yazdır
Yazdıktan sonra desteği çıkarmak için parçayı su ile durla
Malzeme support+model yazdırma için PLA ile kombinlenebilir
Destek Ayarları
PVA is itself a support material. Dissolve in warm water (up to 45°C) after printing. Set support interface Z-distance to 0mm for water-soluble supports.
Bambu Lab H2D Pro Specs
| Build Volume | 350 x 320 x 325 mm |
| Max Speed | 1000 mm/s |
| Max Nozzle Temp | 350°C |
| Max Bed Temp | 120°C |
| Extruder | Direct Drive |
PVA Properties
| Nozzle Range | 185-215°C |
| Bed Range | 50-60°C |
| Speed Range | 20-30 mm/s |
| Difficulty | intermediate |
| Drying | 50°C / 5h |
| Enclosure | Not needed |
PVA Bir Bakışta
Güçlü Yönleri
- Water-soluble support material
- Leaves near-perfect supported surfaces
- Dissolves in tap water (2-12 hours)
- Best paired with PLA
- No manual support removal needed
Zayıf Yönleri
- Extremely moisture sensitive (dissolves in water)
- Expensive (~$40-60/kg)
- Requires dual-extruder setup
- Must be stored in airtight container at all times
- Brittle when moisture-damaged
Kişiselleştirilmiş yapay zeka ayarları ister misin?
Tam kurulumunu ve ne yazdırdığını açıkla. 3DSearch'ün yapay zeka uzmanı saniyeler içinde PVA ile Bambu Lab H2D Pro için özel slicer ayarları oluşturuyor.
3DSearch'ü dene →Kaynaklar: Based on Bambu Lab Wiki (wiki.bambulab.com), community testing data, manufacturer recommended ranges. Değerler filament belirtimleri ve yazıcı donanım sınırlarından hesaplanmıştır.