Recycled PETG Settings for Bambu Lab A1 Combo
Recommended slicer settings for printing Recycled PETG on the Bambu Lab A1 Combo (256 x 256 x 256 mm build volume, 500 mm/s max speed, direct drive extruder).
Slicer Configuration
Copy these values into your slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Setting | Value | Range |
|---|---|---|
| Nozzle Temperature | 238°C | 225-250°C |
| Bed Temperature | 83°C | 75-90°C |
| First Layer Nozzle | 243°C | +5°C above normal |
| First Layer Bed | 88°C | +5°C above normal |
| Print Speed | 40 mm/s | 30-50 mm/s |
| First Layer Speed | 15 mm/s | 25-50% of normal |
| Wall Speed | 30 mm/s | 70-80% of normal |
| Travel Speed | 75 mm/s | 120-150% of print speed |
| Layer Height | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Wall Count | 2-3 | Perimeters/shells |
| Top/Bottom Layers | 3-4 | Solid layers |
| Cooling Fan | 100% | From layer 2+ |
| Retraction Distance | 0.8-1.2 mm | Direct drive |
| Retraction Speed | 40 mm/s | Direct drive |
Before You Print
Print Quality Profiles
Three presets for common use cases with Recycled PETG on the Bambu Lab A1 Combo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Bed Adhesion
Recycled PETG adheres like standard PETG — sometimes too well. Use a textured PEI sheet or apply glue stick as a release agent on smooth PEI. Let the bed cool fully before removing prints.
Temperature Tuning Guide
Nozzle: 238°C
Range: 225-250°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 83°C
Range: 75-90°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Troubleshooting Recycled PETG on Bambu Lab A1 Combo
Pro Tips for Recycled PETG
Treat recycled PETG the same as standard PETG -- dry before use, 30-50% fan, glue stick on smooth PEI
Quality varies between brands; find a reliable supplier and stick with them
Recycled PETG is more eco-friendly with nearly identical mechanical properties to virgin PETG
Some batches may have slightly more stringing; tune retraction per spool
Support Settings
For prints requiring supports with Recycled PETG, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Bambu Lab A1 Combo Specs
| Build Volume | 256 x 256 x 256 mm |
| Max Speed | 500 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 100°C |
| Extruder | Direct Drive |
Recycled PETG Properties
| Nozzle Range | 225-250°C |
| Bed Range | 75-90°C |
| Speed Range | 30-50 mm/s |
| Difficulty | beginner |
| Drying | 65°C / 7h |
| Enclosure | Not needed |
Recycled PETG at a Glance
Strengths
- Eco-friendly recycled material
- Similar properties to virgin PETG
- Good impact and chemical resistance
- Reduces plastic waste
Weaknesses
- Color consistency may vary
- Slightly more stringing than virgin PETG
- Limited color options
Want personalized AI settings?
Describe your exact setup and what you are printing. 3DSearch's AI expert generates custom slicer settings for your Bambu Lab A1 Combo with Recycled PETG in seconds.
Try 3DSearch →Sources: Based on Bambu Lab Wiki (wiki.bambulab.com), community testing data, manufacturer recommended ranges. Values calculated from filament specifications and printer hardware limits.