Silk PLA Settings for Anycubic Kobra 2 Neo
Recommended slicer settings for printing Silk PLA on the Anycubic Kobra 2 Neo (220 x 220 x 250 mm build volume, 250 mm/s max speed, direct drive extruder).
הגדרות Slicer
העתק את הערכים האלה ל-Slicer שלך (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| הגדרה | ערך | טווח |
|---|---|---|
| טמפרטורת חרירון | 223°C | 215-230°C |
| טמפרטורת משטח | 65°C | 60-70°C |
| חרירון בשכבה ראשונה | 228°C | +5°C above normal |
| משטח בשכבה ראשונה | 70°C | +5°C above normal |
| מהירות הדפסה | 40 mm/s | 30-50 mm/s |
| מהירות שכבה ראשונה | 15 mm/s | 25-50% of normal |
| מהירות דפנות | 30 mm/s | 70-80% of normal |
| מהירות תנועה | 75 mm/s | 120-150% of print speed |
| גובה שכבה | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| מספר דפנות | 2-3 | Perimeters/shells |
| שכבות עליונות/תחתונות | 3-4 | Solid layers |
| מאוורר קירור | 100% | From layer 2+ |
| מרחק נסיגה | 0.8-1.2 mm | Direct drive |
| מהירות נסיגה | 40 mm/s | Direct drive |
לפני שמדפיסים
פרופילי איכות הדפסה
Three presets for common use cases with Silk PLA on the Anycubic Kobra 2 Neo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
היצמדות למשטח
Silk PLA uses the same adhesion as regular PLA. A clean PEI sheet is ideal. The shiny finish can make it slightly harder to get a good first layer, so increase bed temperature by 5°C if needed.
מדריך כיוון טמפרטורה
Nozzle: 223°C
Range: 215-230°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 65°C
Range: 60-70°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
פתרון תקלות Silk PLA על Anycubic Kobra 2 Neo
טיפים מקצועיים ל-Silk PLA
Print at the hotter end (215-225°C) for maximum metallic sheen and shine
Medium print speed gives the best surface finish -- too fast reduces the glossy effect
Lower infill density helps the outer walls look smoother and more reflective
Silk PLA is purely decorative -- do not use it for functional or load-bearing parts
Combine with good lighting in your display area to maximize the visual impact of the silk finish
הגדרות תמיכות
For prints requiring supports with Silk PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 2 Neo Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 250 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
Silk PLA Properties
| Nozzle Range | 215-230°C |
| Bed Range | 60-70°C |
| Speed Range | 30-50 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
Silk PLA במבט מהיר
יתרונות
- Beautiful glossy, metallic-like finish
- Very popular for decorative prints
- Available in many vibrant colors
- Easy to print (PLA base)
- Stunning visual results with minimal effort
חסרונות
- More brittle than regular PLA
- Not suitable for functional parts (purely decorative)
- Medium speeds needed for best sheen
- Slightly higher print temperature than PLA
רוצה הגדרות AI מותאמות אישית?
תאר את ההגדרה המדויקת שלך ואת מה שאתה מדפיס. מומחה ה-AI של 3DSearch מייצר הגדרות סלייסר מותאמות עבור ה-Anycubic Kobra 2 Neo שלך עם Silk PLA תוך שניות.
נסה את 3DSearch →מקורות: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. הערכים חושבו ממפרטי הפילמנט וממגבלות החומרה של המדפסת.