BVOH Settings for QIDI Q1 Pro
Recommended slicer settings for printing BVOH on the QIDI Q1 Pro (245 x 245 x 245 mm build volume, 600 mm/s max speed, direct drive extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 205°C | 190-220°C |
| درجة حرارة المنصة | 55°C | 50-60°C |
| الفوهة للطبقة الأولى | 210°C | +5°C above normal |
| المنصة للطبقة الأولى | 60°C | +5°C above normal |
| سرعة الطباعة | 30 mm/s | 20-40 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 23 mm/s | 70-80% of normal |
| سرعة الانتقال | 60 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 0.8-1.2 mm | Direct drive |
| سرعة السحب | 40 mm/s | Direct drive |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with BVOH on the QIDI Q1 Pro.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 40 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 30 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 20 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
BVOH is a water-soluble support material similar to PVA. It adheres to whatever build surface your main material uses. Use a bed temperature of 50-70°C. BVOH dissolves faster than PVA in warm water.
دليل ضبط درجة الحرارة
Nozzle: 205°C
Range: 190-220°C. Printer max: 350°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 55°C
Range: 50-60°C. Printer max: 120°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء BVOH على QIDI Q1 Pro
نصائح احترافية لـ BVOH
Store BVOH sealed with desiccant at ALL times -- it literally dissolves in moisture from the air
Print from a dry box; even 30 minutes of ambient exposure can damage BVOH in humid climates
BVOH dissolves in warm water (40-50°C) faster than PVA; change water periodically
Use BVOH with PLA or PETG as the main material; temperature compatibility is important
إعدادات الدعائم
For prints requiring supports with BVOH, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
QIDI Q1 Pro Specs
| Build Volume | 245 x 245 x 245 mm |
| Max Speed | 600 mm/s |
| Max Nozzle Temp | 350°C |
| Max Bed Temp | 120°C |
| Extruder | Direct Drive |
BVOH Properties
| Nozzle Range | 190-220°C |
| Bed Range | 50-60°C |
| Speed Range | 20-40 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
BVOH في لمحة
نقاط القوة
- Water-soluble support material
- Dissolves faster than PVA (2-4 hours)
- Works with wider range of build materials
- Leaves very clean supported surfaces
نقاط الضعف
- Extremely moisture sensitive — use immediately after opening
- More expensive than PVA
- Must store in sealed dry container
- Limited shelf life once opened
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك QIDI Q1 Pro مع BVOH خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.