PP Settings for QIDI Q1 Pro
Recommended slicer settings for printing PP on the QIDI Q1 Pro (245 x 245 x 245 mm build volume, 600 mm/s max speed, direct drive extruder).
Slicer Configuration
Copy these values into your slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Setting | Value | Range |
|---|---|---|
| Nozzle Temperature | 235°C | 220-250°C |
| Bed Temperature | 93°C | 85-100°C |
| First Layer Nozzle | 240°C | +5°C above normal |
| First Layer Bed | 98°C | +5°C above normal |
| Print Speed | 30 mm/s | 20-40 mm/s |
| First Layer Speed | 15 mm/s | 25-50% of normal |
| Wall Speed | 23 mm/s | 70-80% of normal |
| Travel Speed | 60 mm/s | 120-150% of print speed |
| Layer Height | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Wall Count | 2-3 | Perimeters/shells |
| Top/Bottom Layers | 3-4 | Solid layers |
| Cooling Fan | 100% | From layer 2+ |
| Retraction Distance | 0.8-1.2 mm | Direct drive |
| Retraction Speed | 40 mm/s | Direct drive |
Before You Print
Print Quality Profiles
Three presets for common use cases with PP on the QIDI Q1 Pro.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 40 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 30 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 20 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Bed Adhesion
PP (polypropylene) does not stick to standard build surfaces. You MUST use a PP packing tape surface or a dedicated PP build plate. Standard PEI, glass, and painter's tape will NOT work. A brim covering the entire first layer is essential. PP shrinks significantly, so expect some warping even with proper adhesion.
Temperature Tuning Guide
Nozzle: 235°C
Range: 220-250°C. Printer max: 350°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 93°C
Range: 85-100°C. Printer max: 120°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Troubleshooting PP on QIDI Q1 Pro
Pro Tips for PP
PP requires a polypropylene packing tape surface or dedicated PP build plate -- standard surfaces do not work
Expect significant warping even with proper setup; keep parts small or use living-hinge designs that accommodate shrinkage
PP is chemically resistant, flexible, and food-safe -- ideal for containers and hinges
Fan at 0-10%; PP needs to stay warm for proper layer bonding
Support Settings
For prints requiring supports with PP, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
QIDI Q1 Pro Specs
| Build Volume | 245 x 245 x 245 mm |
| Max Speed | 600 mm/s |
| Max Nozzle Temp | 350°C |
| Max Bed Temp | 120°C |
| Extruder | Direct Drive |
PP Properties
| Nozzle Range | 220-250°C |
| Bed Range | 85-100°C |
| Speed Range | 20-40 mm/s |
| Difficulty | advanced |
| Drying | 55°C / 6h |
| Enclosure | Not needed |
PP at a Glance
Strengths
- Chemically inert — resists most solvents and acids
- Flexible living hinges
- Fatigue resistant — can be bent repeatedly
- Food-safe and lightweight
Weaknesses
- Terrible bed adhesion — needs PP tape or packing tape
- Warps severely
- Very difficult to bond or glue
- Limited color availability
Want personalized AI settings?
Describe your exact setup and what you are printing. 3DSearch's AI expert generates custom slicer settings for your QIDI Q1 Pro with PP in seconds.
Try 3DSearch →Sources: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Values calculated from filament specifications and printer hardware limits.