Matte PLA Settings for Bambu Lab H2C
Recommended slicer settings for printing Matte PLA on the Bambu Lab H2C (330 x 320 x 325 mm build volume, 1000 mm/s max speed, direct drive extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 210°C | 195-225°C |
| درجة حرارة المنصة | 58°C | 50-65°C |
| الفوهة للطبقة الأولى | 215°C | +5°C above normal |
| المنصة للطبقة الأولى | 63°C | +5°C above normal |
| سرعة الطباعة | 50 mm/s | 40-60 mm/s |
| سرعة الطبقة الأولى | 20 mm/s | 25-50% of normal |
| سرعة الجدران | 38 mm/s | 70-80% of normal |
| سرعة الانتقال | 90 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 0.8-1.2 mm | Direct drive |
| سرعة السحب | 40 mm/s | Direct drive |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with Matte PLA on the Bambu Lab H2C.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 60 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 50 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 40 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
Matte PLA adheres the same way as regular PLA. A clean PEI sheet (smooth or textured) works perfectly. For glass beds, use glue stick or hairspray. Clean with IPA before each print.
دليل ضبط درجة الحرارة
Nozzle: 210°C
Range: 195-225°C. Printer max: 350°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 58°C
Range: 50-65°C. Printer max: 120°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء Matte PLA على Bambu Lab H2C
نصائح احترافية لـ Matte PLA
Matte PLA hides layer lines better than glossy PLA -- great for display prints where you want a clean look
Print at 200-215°C; matte finishes can look uneven at temperatures that are too high
Storage is the same as regular PLA: airtight container with desiccant
Matte PLA sands and paints very well due to its non-reflective surface
إعدادات الدعائم
For prints requiring supports with Matte PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Bambu Lab H2C Specs
| Build Volume | 330 x 320 x 325 mm |
| Max Speed | 1000 mm/s |
| Max Nozzle Temp | 350°C |
| Max Bed Temp | 120°C |
| Extruder | Direct Drive |
Matte PLA Properties
| Nozzle Range | 195-225°C |
| Bed Range | 50-65°C |
| Speed Range | 40-60 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
Matte PLA في لمحة
نقاط القوة
- Beautiful non-reflective matte surface finish
- Hides layer lines better than standard PLA
- Same ease of printing as PLA
- Available in wide color range
نقاط الضعف
- Slightly weaker than standard PLA
- Surface scratches more visibly
- More expensive than regular PLA
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Bambu Lab H2C مع Matte PLA خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on Bambu Lab Wiki (wiki.bambulab.com), community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.