Recycled PETG Settings for Anycubic Kobra 3 Combo
Recommended slicer settings for printing Recycled PETG on the Anycubic Kobra 3 Combo (250 x 250 x 260 mm build volume, 600 mm/s max speed, direct drive extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 238°C | 225-250°C |
| درجة حرارة المنصة | 83°C | 75-90°C |
| الفوهة للطبقة الأولى | 243°C | +5°C above normal |
| المنصة للطبقة الأولى | 88°C | +5°C above normal |
| سرعة الطباعة | 40 mm/s | 30-50 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 30 mm/s | 70-80% of normal |
| سرعة الانتقال | 75 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 0.8-1.2 mm | Direct drive |
| سرعة السحب | 40 mm/s | Direct drive |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with Recycled PETG on the Anycubic Kobra 3 Combo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
Recycled PETG adheres like standard PETG — sometimes too well. Use a textured PEI sheet or apply glue stick as a release agent on smooth PEI. Let the bed cool fully before removing prints.
دليل ضبط درجة الحرارة
Nozzle: 238°C
Range: 225-250°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 83°C
Range: 75-90°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء Recycled PETG على Anycubic Kobra 3 Combo
نصائح احترافية لـ Recycled PETG
Treat recycled PETG the same as standard PETG -- dry before use, 30-50% fan, glue stick on smooth PEI
Quality varies between brands; find a reliable supplier and stick with them
Recycled PETG is more eco-friendly with nearly identical mechanical properties to virgin PETG
Some batches may have slightly more stringing; tune retraction per spool
إعدادات الدعائم
For prints requiring supports with Recycled PETG, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 3 Combo Specs
| Build Volume | 250 x 250 x 260 mm |
| Max Speed | 600 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
Recycled PETG Properties
| Nozzle Range | 225-250°C |
| Bed Range | 75-90°C |
| Speed Range | 30-50 mm/s |
| Difficulty | beginner |
| Drying | 65°C / 7h |
| Enclosure | Not needed |
Recycled PETG في لمحة
نقاط القوة
- Eco-friendly recycled material
- Similar properties to virgin PETG
- Good impact and chemical resistance
- Reduces plastic waste
نقاط الضعف
- Color consistency may vary
- Slightly more stringing than virgin PETG
- Limited color options
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Anycubic Kobra 3 Combo مع Recycled PETG خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.