PC Settings for Anycubic Kobra 3 Combo
Recommended slicer settings for printing PC on the Anycubic Kobra 3 Combo (250 x 250 x 260 mm build volume, 600 mm/s max speed, direct drive extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 285°C | 260-310°C |
| درجة حرارة المنصة | 110°C | 100-120°C |
| الفوهة للطبقة الأولى | 290°C | +5°C above normal |
| المنصة للطبقة الأولى | 110°C | At printer max |
| سرعة الطباعة | 30 mm/s | 20-40 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 23 mm/s | 70-80% of normal |
| سرعة الانتقال | 60 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 0-10% | From layer 2+ |
| مسافة السحب | 0.8-1.2 mm | Direct drive |
| سرعة السحب | 40 mm/s | Direct drive |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with PC on the Anycubic Kobra 3 Combo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 40 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 30 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 20 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
Polycarbonate needs very high bed temperatures and excellent adhesion. Use a PEI sheet at maximum bed temperature. Apply glue stick as a release agent (PC can bond too strongly). A brim is essential. Consider Magigoo PC specialty adhesive for best results.
دليل ضبط درجة الحرارة
Nozzle: 285°C
Range: 260-310°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 110°C
Range: 100-120°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء PC على Anycubic Kobra 3 Combo
نصائح احترافية لـ PC
PC is the most demanding common filament to print -- make sure your setup is fully prepared
An all-metal hotend is mandatory; PTFE-lined hotends will degrade at PC temperatures
Seal your enclosure as thoroughly as possible for the best results
Use glue stick as a release agent -- PC can bond so strongly to PEI that it damages the sheet
If you are new to high-temp printing, try ABS or ASA first before attempting polycarbonate
إعدادات الدعائم
For prints requiring supports with PC, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 3 Combo Specs
| Build Volume | 250 x 250 x 260 mm |
| Max Speed | 600 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
PC Properties
| Nozzle Range | 260-310°C |
| Bed Range | 100-120°C |
| Speed Range | 20-40 mm/s |
| Difficulty | advanced |
| Drying | 80°C / 10h |
| Enclosure | Recommended |
PC في لمحة
نقاط القوة
- Arguably the toughest non-flexible filament
- Excellent heat resistance (softens ~150C)
- Can withstand repeated impacts without shattering
- Can print in translucent/clear
- Ideal for protective equipment and high-temp parts
نقاط الضعف
- Requires all-metal hotend
- Severe warping without heated enclosure
- Very high printing temperatures
- High moisture sensitivity
- Most demanding common filament to print
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Anycubic Kobra 3 Combo مع PC خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.