Conductive PLA Settings for Anycubic Kobra 3 Combo
Recommended slicer settings for printing Conductive PLA on the Anycubic Kobra 3 Combo (250 x 250 x 260 mm build volume, 600 mm/s max speed, direct drive extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 215°C | 200-230°C |
| درجة حرارة المنصة | 55°C | 50-60°C |
| الفوهة للطبقة الأولى | 220°C | +5°C above normal |
| المنصة للطبقة الأولى | 60°C | +5°C above normal |
| سرعة الطباعة | 30 mm/s | 20-40 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 23 mm/s | 70-80% of normal |
| سرعة الانتقال | 60 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 0.8-1.2 mm | Direct drive |
| سرعة السحب | 40 mm/s | Direct drive |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with Conductive PLA on the Anycubic Kobra 3 Combo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 40 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 30 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 20 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
Conductive PLA adheres like standard PLA. Use a clean PEI sheet or glass bed with glue stick. Handle prints carefully — the conductive carbon particles can leave residue on build surfaces.
دليل ضبط درجة الحرارة
Nozzle: 215°C
Range: 200-230°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 55°C
Range: 50-60°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء Conductive PLA على Anycubic Kobra 3 Combo
نصائح احترافية لـ Conductive PLA
Resistance varies with print orientation; Z-axis conductivity is lower than XY-axis
Print at consistent speed and temperature for the most uniform electrical properties
Best for capacitive touch sensors, LED circuits, and low-voltage applications
Not suitable for high-current applications; resistance is in the kOhm range per cm
إعدادات الدعائم
For prints requiring supports with Conductive PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 3 Combo Specs
| Build Volume | 250 x 250 x 260 mm |
| Max Speed | 600 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
Conductive PLA Properties
| Nozzle Range | 200-230°C |
| Bed Range | 50-60°C |
| Speed Range | 20-40 mm/s |
| Difficulty | intermediate |
| Drying | Not required |
| Enclosure | Not needed |
Conductive PLA في لمحة
نقاط القوة
- Electrically conductive — can create touch sensors
- Useful for prototyping simple circuits
- Prints on standard PLA settings
- Enables embedded electronics in prints
نقاط الضعف
- High resistance — not suitable for power circuits
- Conductivity varies with print orientation
- Limited to black color
- More expensive than standard PLA
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Anycubic Kobra 3 Combo مع Conductive PLA خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.