Silk PLA Settings for Anycubic Kobra 2 Neo
Recommended slicer settings for printing Silk PLA on the Anycubic Kobra 2 Neo (220 x 220 x 250 mm build volume, 250 mm/s max speed, direct drive extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 223°C | 215-230°C |
| درجة حرارة المنصة | 65°C | 60-70°C |
| الفوهة للطبقة الأولى | 228°C | +5°C above normal |
| المنصة للطبقة الأولى | 70°C | +5°C above normal |
| سرعة الطباعة | 40 mm/s | 30-50 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 30 mm/s | 70-80% of normal |
| سرعة الانتقال | 75 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 0.8-1.2 mm | Direct drive |
| سرعة السحب | 40 mm/s | Direct drive |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with Silk PLA on the Anycubic Kobra 2 Neo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
Silk PLA uses the same adhesion as regular PLA. A clean PEI sheet is ideal. The shiny finish can make it slightly harder to get a good first layer, so increase bed temperature by 5°C if needed.
دليل ضبط درجة الحرارة
Nozzle: 223°C
Range: 215-230°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 65°C
Range: 60-70°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء Silk PLA على Anycubic Kobra 2 Neo
نصائح احترافية لـ Silk PLA
Print at the hotter end (215-225°C) for maximum metallic sheen and shine
Medium print speed gives the best surface finish -- too fast reduces the glossy effect
Lower infill density helps the outer walls look smoother and more reflective
Silk PLA is purely decorative -- do not use it for functional or load-bearing parts
Combine with good lighting in your display area to maximize the visual impact of the silk finish
إعدادات الدعائم
For prints requiring supports with Silk PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 2 Neo Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 250 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
Silk PLA Properties
| Nozzle Range | 215-230°C |
| Bed Range | 60-70°C |
| Speed Range | 30-50 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
Silk PLA في لمحة
نقاط القوة
- Beautiful glossy, metallic-like finish
- Very popular for decorative prints
- Available in many vibrant colors
- Easy to print (PLA base)
- Stunning visual results with minimal effort
نقاط الضعف
- More brittle than regular PLA
- Not suitable for functional parts (purely decorative)
- Medium speeds needed for best sheen
- Slightly higher print temperature than PLA
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Anycubic Kobra 2 Neo مع Silk PLA خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.