PA6 Settings for Anycubic Kobra 2 Neo
Recommended slicer settings for printing PA6 on the Anycubic Kobra 2 Neo (220 x 220 x 250 mm build volume, 250 mm/s max speed, direct drive extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 255°C | 240-270°C |
| درجة حرارة المنصة | 90°C | 80-100°C |
| الفوهة للطبقة الأولى | 260°C | +5°C above normal |
| المنصة للطبقة الأولى | 95°C | +5°C above normal |
| سرعة الطباعة | 40 mm/s | 30-50 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 30 mm/s | 70-80% of normal |
| سرعة الانتقال | 75 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 0.8-1.2 mm | Direct drive |
| سرعة السحب | 40 mm/s | Direct drive |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with PA6 on the Anycubic Kobra 2 Neo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
PA6 nylon requires Garolite (G10) sheet or PEI with Magigoo PA adhesive at 80-100°C. A brim is essential. PA6 warps aggressively and must be printed from a dry box. Blue painter's tape with glue stick is an alternative.
دليل ضبط درجة الحرارة
Nozzle: 255°C
Range: 240-270°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 90°C
Range: 80-100°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء PA6 على Anycubic Kobra 2 Neo
نصائح احترافية لـ PA6
PA6 is harder to print than PA12 nylon -- start with PA12 if you are new to nylon
Drying is absolutely critical: 80°C for 16-20 hours, then print from a dry box
Garolite (G10) sheets provide the best bed adhesion for PA6
After printing, moisture-conditioning (boiling) PA6 parts can triple their impact strength
إعدادات الدعائم
For prints requiring supports with PA6, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 2 Neo Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 250 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
PA6 Properties
| Nozzle Range | 240-270°C |
| Bed Range | 80-100°C |
| Speed Range | 30-50 mm/s |
| Difficulty | advanced |
| Drying | 85°C / 12h |
| Enclosure | Recommended |
PA6 في لمحة
نقاط القوة
- Strongest common nylon variant
- Exceptional wear and fatigue resistance
- Good chemical resistance
- Excellent for gears, bearings, hinges
نقاط الضعف
- Extremely hygroscopic — must dry extensively
- Warps aggressively without enclosure
- Difficult bed adhesion
- Shrinks significantly during cooling
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Anycubic Kobra 2 Neo مع PA6 خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.