Matte PLA Settings for Anycubic Kobra 2 Neo
Recommended slicer settings for printing Matte PLA on the Anycubic Kobra 2 Neo (220 x 220 x 250 mm build volume, 250 mm/s max speed, direct drive extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 210°C | 195-225°C |
| درجة حرارة المنصة | 58°C | 50-65°C |
| الفوهة للطبقة الأولى | 215°C | +5°C above normal |
| المنصة للطبقة الأولى | 63°C | +5°C above normal |
| سرعة الطباعة | 50 mm/s | 40-60 mm/s |
| سرعة الطبقة الأولى | 20 mm/s | 25-50% of normal |
| سرعة الجدران | 38 mm/s | 70-80% of normal |
| سرعة الانتقال | 90 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 0.8-1.2 mm | Direct drive |
| سرعة السحب | 40 mm/s | Direct drive |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with Matte PLA on the Anycubic Kobra 2 Neo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 60 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 50 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 40 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
Matte PLA adheres the same way as regular PLA. A clean PEI sheet (smooth or textured) works perfectly. For glass beds, use glue stick or hairspray. Clean with IPA before each print.
دليل ضبط درجة الحرارة
Nozzle: 210°C
Range: 195-225°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 58°C
Range: 50-65°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء Matte PLA على Anycubic Kobra 2 Neo
نصائح احترافية لـ Matte PLA
Matte PLA hides layer lines better than glossy PLA -- great for display prints where you want a clean look
Print at 200-215°C; matte finishes can look uneven at temperatures that are too high
Storage is the same as regular PLA: airtight container with desiccant
Matte PLA sands and paints very well due to its non-reflective surface
إعدادات الدعائم
For prints requiring supports with Matte PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 2 Neo Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 250 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
Matte PLA Properties
| Nozzle Range | 195-225°C |
| Bed Range | 50-65°C |
| Speed Range | 40-60 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
Matte PLA في لمحة
نقاط القوة
- Beautiful non-reflective matte surface finish
- Hides layer lines better than standard PLA
- Same ease of printing as PLA
- Available in wide color range
نقاط الضعف
- Slightly weaker than standard PLA
- Surface scratches more visibly
- More expensive than regular PLA
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Anycubic Kobra 2 Neo مع Matte PLA خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.