PHA Settings for Bambu Lab X1 Carbon
Recommended slicer settings for printing PHA on the Bambu Lab X1 Carbon (256 x 256 x 256 mm build volume, 500 mm/s max speed, direct drive extruder).
切片配置
将这些参数复制到你的切片软件（Cura、OrcaSlicer、PrusaSlicer、Bambu Studio）| 参数 | 数值 | 范围 |
|---|---|---|
| 喷嘴温度 | 188°C | 175-200°C |
| 热床温度 | 50°C | 40-60°C |
| 首层喷嘴 | 193°C | +5°C above normal |
| 首层热床 | 55°C | +5°C above normal |
| 打印速度 | 35 mm/s | 25-45 mm/s |
| 首层速度 | 15 mm/s | 25-50% of normal |
| 外壁速度 | 26 mm/s | 70-80% of normal |
| 空走速度 | 68 mm/s | 120-150% of print speed |
| 层高 | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| 壁数 | 2-3 | Perimeters/shells |
| 顶层/底层 | 3-4 | Solid layers |
| 散热风扇 | 100% | From layer 2+ |
| 回抽距离 | 0.8-1.2 mm | Direct drive |
| 回抽速度 | 40 mm/s | Direct drive |
开始打印前
打印质量预设
Three presets for common use cases with PHA on the Bambu Lab X1 Carbon.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 45 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 35 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 25 mm/s | 20-30% | Miniatures, display pieces, fine detail |
热床附着
PHA(聚羟基烷酸酯)与 PLA 类似粘合。在 50-60°C 使用干净的 PEI 片或玻璃热床配胶棒。PHA 是生物可降解的,比 PLA 略微更柔性。
温度调校指南
Nozzle: 188°C
Range: 175-200°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 50°C
Range: 40-60°C. Printer max: 120°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
在 Bambu Lab X1 Carbon 上打印 PHA 的问题排查
PHA 使用技巧
PHA 完全生物可降解和可堆肥 -- PLA 的更绿色替代品
打印设置与 PLA 非常相似;从 PLA 设置开始并从那里调整
PHA 比 PLA 略微更柔性,冲击时脆性更少
储存在凉爽、干燥的地方;PHA 在湿度环境中生物降解更快
支撑设置
For prints requiring supports with PHA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Bambu Lab X1 Carbon Specs
| Build Volume | 256 x 256 x 256 mm |
| Max Speed | 500 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 120°C |
| Extruder | Direct Drive |
PHA Properties
| Nozzle Range | 175-200°C |
| Bed Range | 40-60°C |
| Speed Range | 25-45 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
PHA 速览
优势
- Fully biodegradable in soil and marine environments
- Renewable bioplastic from bacterial fermentation
- Non-toxic and biocompatible
- Easier to print than PLA in some cases
劣势
- Lower heat resistance than PLA (~55°C)
- More expensive than PLA
- Limited availability and color options
- Slower degradation rate than marketed
想要个性化的 AI 参数？
描述你的具体配置和要打印的内容。3DSearch 的 AI 专家会在几秒内为你的 Bambu Lab X1 Carbon 搭配 PHA 生成定制切片参数。
试用 3DSearch →来源： Based on Bambu Lab Wiki (wiki.bambulab.com), community testing data, manufacturer recommended ranges. 参数根据耗材规格和打印机硬件上限计算得出。