Glass-fiber PETG Settings for Bambu Lab X1 Carbon
Recommended slicer settings for printing Glass-fiber PETG on the Bambu Lab X1 Carbon (256 x 256 x 256 mm build volume, 500 mm/s max speed, direct drive extruder).
切片配置
将这些参数复制到你的切片软件（Cura、OrcaSlicer、PrusaSlicer、Bambu Studio）| 参数 | 数值 | 范围 |
|---|---|---|
| 喷嘴温度 | 248°C | 235-260°C |
| 热床温度 | 88°C | 80-95°C |
| 首层喷嘴 | 253°C | +5°C above normal |
| 首层热床 | 93°C | +5°C above normal |
| 打印速度 | 40 mm/s | 30-50 mm/s |
| 首层速度 | 15 mm/s | 25-50% of normal |
| 外壁速度 | 30 mm/s | 70-80% of normal |
| 空走速度 | 75 mm/s | 120-150% of print speed |
| 层高 | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| 壁数 | 2-3 | Perimeters/shells |
| 顶层/底层 | 3-4 | Solid layers |
| 散热风扇 | 100% | From layer 2+ |
| 回抽距离 | 0.8-1.2 mm | Direct drive |
| 回抽速度 | 40 mm/s | Direct drive |
开始打印前
打印质量预设
Three presets for common use cases with Glass-fiber PETG on the Bambu Lab X1 Carbon.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
热床附着
玻璃纤维 PETG 与标准 PETG 粘合。在光滑 PEI 上使用有纹理的 PEI 片或胶棒作为脱模剂。玻璃纤维与普通 PETG 相比减少翘曲。硬化钢喷嘴是必需的。
温度调校指南
Nozzle: 248°C
Range: 235-260°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 88°C
Range: 80-95°C. Printer max: 120°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
在 Bambu Lab X1 Carbon 上打印 Glass-fiber PETG 的问题排查
Glass-fiber PETG 使用技巧
硬化钢喷嘴(0.5mm+)是强制的 -- 玻璃纤维甚至比碳纤维更磨料
在 65°C 下彻底干燥 8 小时后打印
比普通 PETG 慢 30% 打印以获得最佳表面质量
玻璃纤维 PETG 比碳纤维 PETG 更硬但略弱;适合尺寸稳定性
支撑设置
For prints requiring supports with Glass-fiber PETG, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Bambu Lab X1 Carbon Specs
| Build Volume | 256 x 256 x 256 mm |
| Max Speed | 500 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 120°C |
| Extruder | Direct Drive |
Glass-fiber PETG Properties
| Nozzle Range | 235-260°C |
| Bed Range | 80-95°C |
| Speed Range | 30-50 mm/s |
| Difficulty | intermediate |
| Drying | 65°C / 7h |
| Enclosure | Not needed |
Glass-fiber PETG 速览
优势
- Much stiffer than standard PETG
- Better heat resistance than plain PETG
- Good dimensional stability
- Less expensive than carbon fiber composites
劣势
- Hardened steel nozzle required
- Increased brittleness vs standard PETG
- Use 0.5mm+ nozzle to prevent clogging
- Rougher surface finish
想要个性化的 AI 参数？
描述你的具体配置和要打印的内容。3DSearch 的 AI 专家会在几秒内为你的 Bambu Lab X1 Carbon 搭配 Glass-fiber PETG 生成定制切片参数。
试用 3DSearch →来源： Based on Bambu Lab Wiki (wiki.bambulab.com), community testing data, manufacturer recommended ranges. 参数根据耗材规格和打印机硬件上限计算得出。