Breakaway Support Settings for Bambu Lab A1 Mini
Recommended slicer settings for printing Breakaway Support on the Bambu Lab A1 Mini (180 x 180 x 180 mm build volume, 500 mm/s max speed, direct drive extruder).
切片配置
将这些参数复制到你的切片软件（Cura、OrcaSlicer、PrusaSlicer、Bambu Studio）| 参数 | 数值 | 范围 |
|---|---|---|
| 喷嘴温度 | 225°C | 210-240°C |
| 热床温度 | 60°C | 50-70°C |
| 首层喷嘴 | 230°C | +5°C above normal |
| 首层热床 | 65°C | +5°C above normal |
| 打印速度 | 40 mm/s | 30-50 mm/s |
| 首层速度 | 15 mm/s | 25-50% of normal |
| 外壁速度 | 30 mm/s | 70-80% of normal |
| 空走速度 | 75 mm/s | 120-150% of print speed |
| 层高 | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| 壁数 | 2-3 | Perimeters/shells |
| 顶层/底层 | 3-4 | Solid layers |
| 散热风扇 | 100% | From layer 2+ |
| 回抽距离 | 0.8-1.2 mm | Direct drive |
| 回抽速度 | 40 mm/s | Direct drive |
开始打印前
打印质量预设
Three presets for common use cases with Breakaway Support on the Bambu Lab A1 Mini.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
热床附着
断裂支撑材料粘合到你的主要材料使用的任何热床表面。热床温度应匹配主耗材。打印后,机械地折断支撑 -- 无需溶剂。
温度调校指南
Nozzle: 225°C
Range: 210-240°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 60°C
Range: 50-70°C. Printer max: 80°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
在 Bambu Lab A1 Mini 上打印 Breakaway Support 的问题排查
Breakaway Support 使用技巧
断裂支撑机械地折断 -- 无需溶剂或水
调整 Z 间隙和界面密度以平衡支撑强度与移除容易度
对于简单悬垂,断裂比可溶解支撑更快移除
对于复杂内部几何体使用可溶解支撑,机械访问困难
支撑设置
For prints requiring supports with Breakaway Support, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Bambu Lab A1 Mini Specs
| Build Volume | 180 x 180 x 180 mm |
| Max Speed | 500 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 80°C |
| Extruder | Direct Drive |
Breakaway Support Properties
| Nozzle Range | 210-240°C |
| Bed Range | 50-70°C |
| Speed Range | 30-50 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
Breakaway Support 速览
优势
- Snaps off cleanly without solvents
- Fast removal — no dissolving wait time
- Works with most build materials
- No special post-processing needed
劣势
- Leaves rougher surface than dissolved supports
- Requires accessible support geometry
- Not suitable for internal cavities
- May need pliers for tight areas
想要个性化的 AI 参数？
描述你的具体配置和要打印的内容。3DSearch 的 AI 专家会在几秒内为你的 Bambu Lab A1 Mini 搭配 Breakaway Support 生成定制切片参数。
试用 3DSearch →来源： Based on Bambu Lab Wiki (wiki.bambulab.com), community testing data, manufacturer recommended ranges. 参数根据耗材规格和打印机硬件上限计算得出。