Glow-in-the-dark PLA Settings for Creality Ender 3 S1 Pro
Recommended slicer settings for printing Glow-in-the-dark PLA on the Creality Ender 3 S1 Pro (220 x 220 x 270 mm build volume, 150 mm/s max speed, direct drive extruder).
Slicer Yapılandırması
Bu değerleri slicer'ına (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio) kopyala| Ayar | Değer | Aralık |
|---|---|---|
| Nozzle Sıcaklığı | 210°C | 195-225°C |
| Platform Sıcaklığı | 55°C | 50-60°C |
| İlk Katman Nozzle | 215°C | +5°C above normal |
| İlk Katman Platform | 60°C | +5°C above normal |
| Baskı Hızı | 40 mm/s | 30-50 mm/s |
| İlk Katman Hızı | 15 mm/s | 25-50% of normal |
| Duvar Hızı | 30 mm/s | 70-80% of normal |
| Hareket Hızı | 75 mm/s | 120-150% of print speed |
| Katman Yüksekliği | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Duvar Sayısı | 2-3 | Perimeters/shells |
| Üst/Alt Katmanlar | 3-4 | Solid layers |
| Soğutma Vantilatörü | 100% | From layer 2+ |
| Geri Çekilme Mesafesi | 0.8-1.2 mm | Direct drive |
| Geri Çekilme Hızı | 40 mm/s | Direct drive |
Yazdırmadan Önce
Baskı Kalitesi Profilleri
Three presets for common use cases with Glow-in-the-dark PLA on the Creality Ender 3 S1 Pro.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Platform Yapışması
Karanlıkta Parlayan PLA normal PLA gibi yapışır. Floresans partikülleri yapışmayı etkilemez. Standart PEI veya diğer normal yüzeyler kullan.
Sıcaklık Ayarlama Rehberi
Nozzle: 210°C
Range: 195-225°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 55°C
Range: 50-60°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Glow-in-the-dark PLA ile Creality Ender 3 S1 Pro üzerinde sorun giderme
Glow-in-the-dark PLA için Pro İpuçları
Karanlıkta Parlayan PLA aktivasyon için ışık maruziyetine ihtiyaç duyar - tamamlanan parçaya ışık tut
Normal PLA'ya benzer sıcaklıklarda yazdır (200-220°C)
Parlaklık zaman içinde zayıflayabilir - ışıktan uzakta sakla
Optimal parlaklık için maruz kalma süresi ile deney yap
Malzeme oyuncaklar, dekorasyon ve güvenlik işaretleyicileri için idealdir
Destek Ayarları
For prints requiring supports with Glow-in-the-dark PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Creality Ender 3 S1 Pro Specs
| Build Volume | 220 x 220 x 270 mm |
| Max Speed | 150 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
Glow-in-the-dark PLA Properties
| Nozzle Range | 195-225°C |
| Bed Range | 50-60°C |
| Speed Range | 30-50 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
Glow-in-the-dark PLA Bir Bakışta
Güçlü Yönleri
- Charges in light and glows in the dark
- Fun for decorative and safety items
- Prints like standard PLA
Zayıf Yönleri
- Phosphorescent particles are abrasive — hardened nozzle required
- Limited to green/blue glow colors
- Glow fades over minutes without recharging
- Surface finish is slightly grainy
Kişiselleştirilmiş yapay zeka ayarları ister misin?
Tam kurulumunu ve ne yazdırdığını açıkla. 3DSearch'ün yapay zeka uzmanı saniyeler içinde Glow-in-the-dark PLA ile Creality Ender 3 S1 Pro için özel slicer ayarları oluşturuyor.
3DSearch'ü dene →Kaynaklar: Based on Creality support documentation, community testing data, manufacturer recommended ranges. Değerler filament belirtimleri ve yazıcı donanım sınırlarından hesaplanmıştır.