Glow-in-the-dark PLA Settings for Creality Ender 3 S1 Pro
Recommended slicer settings for printing Glow-in-the-dark PLA on the Creality Ender 3 S1 Pro (220 x 220 x 270 mm build volume, 150 mm/s max speed, direct drive extruder).
Slicer Configuration
Copy these values into your slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Setting | Value | Range |
|---|---|---|
| Nozzle Temperature | 210°C | 195-225°C |
| Bed Temperature | 55°C | 50-60°C |
| First Layer Nozzle | 215°C | +5°C above normal |
| First Layer Bed | 60°C | +5°C above normal |
| Print Speed | 40 mm/s | 30-50 mm/s |
| First Layer Speed | 15 mm/s | 25-50% of normal |
| Wall Speed | 30 mm/s | 70-80% of normal |
| Travel Speed | 75 mm/s | 120-150% of print speed |
| Layer Height | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Wall Count | 2-3 | Perimeters/shells |
| Top/Bottom Layers | 3-4 | Solid layers |
| Cooling Fan | 100% | From layer 2+ |
| Retraction Distance | 0.8-1.2 mm | Direct drive |
| Retraction Speed | 40 mm/s | Direct drive |
Before You Print
Print Quality Profiles
Three presets for common use cases with Glow-in-the-dark PLA on the Creality Ender 3 S1 Pro.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Bed Adhesion
Glow-in-the-dark PLA adheres like regular PLA. A clean PEI sheet or glass with glue stick works well. Note: glow PLA is abrasive and will wear out brass nozzles over time.
Temperature Tuning Guide
Nozzle: 210°C
Range: 195-225°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 55°C
Range: 50-60°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Troubleshooting Glow-in-the-dark PLA on Creality Ender 3 S1 Pro
Pro Tips for Glow-in-the-dark PLA
Use a hardened steel nozzle -- glow particles are abrasive and destroy brass nozzles
Charge prints under bright light or UV for maximum glow intensity and duration
Print with thin walls for better light penetration and stronger glow effect
White or clear glow PLA glows brightest; darker colors glow less
Support Settings
For prints requiring supports with Glow-in-the-dark PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Creality Ender 3 S1 Pro Specs
| Build Volume | 220 x 220 x 270 mm |
| Max Speed | 150 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
Glow-in-the-dark PLA Properties
| Nozzle Range | 195-225°C |
| Bed Range | 50-60°C |
| Speed Range | 30-50 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
Glow-in-the-dark PLA at a Glance
Strengths
- Charges in light and glows in the dark
- Fun for decorative and safety items
- Prints like standard PLA
Weaknesses
- Phosphorescent particles are abrasive — hardened nozzle required
- Limited to green/blue glow colors
- Glow fades over minutes without recharging
- Surface finish is slightly grainy
Want personalized AI settings?
Describe your exact setup and what you are printing. 3DSearch's AI expert generates custom slicer settings for your Creality Ender 3 S1 Pro with Glow-in-the-dark PLA in seconds.
Try 3DSearch →Sources: Based on Creality support documentation, community testing data, manufacturer recommended ranges. Values calculated from filament specifications and printer hardware limits.